Bath accessories: the best bath accessories and tips for choosing them (130 photos and videos)

Banya broom

Most users prefer to make their own, birch or oak are suitable.
This is an indispensable accessory for a DIY bathhouse. The most popular is a broom made from tree branches. It is practical and popular among users. It is important to clear the branches so that nothing interferes with your relaxation. To obtain a therapeutic effect, preparations are made from herbs, in particular wormwood, nettle, and lemon balm. The branches should be collected throughout the summer, because they will not lose their properties in a short period.

For fastening, use a material such as synthetic strong twine. It is important to store finished brooms in a special way. It should be a dark, dry place. Users often store brooms by hanging them in the attic to dry.

Rules for constructing shelves for a steam room

The recommendations below, which explain how to properly install shelves in a bathhouse with a steam room, will ensure the comfort of steaming, guarantee safety and extend the service life of the finishing and bath furniture:

• There should be a ventilation gap of 10 cm between the walls of the steam room and the shelves. When the steps are permanently attached to the walls, this gap is ensured by installing pieces of timber. More precisely, first a beam cut into pieces is attached to the wall, then the frame elements are screwed to it with self-tapping screws with heads recessed into the array.
• The recommended dimensions of the timber for constructing the frame are 50 × 70 mm. The thickness of the board should be four times less than its width so that the wood can dry completely.
• The number of supports is determined by the thickness of the planks. If the thickness of the board is 22 cm, then there should be at least 0.6 m between the supports.
• To ensure stability, it is advisable to tie the frame supports with a board both at the top and bottom along the entire length.
• Rubber pads must be nailed to the bottom surface of the legs of all stationary steps and portable benches.
• Instead of self-tapping screws, it is recommended to use wooden pins, driven into holes drilled for them, or wooden nails as fasteners for flooring boards. If you can’t find anything other than self-tapping screws, it is better to fasten it from the back so that the metal parts do not burn users. Metal heats up much stronger and faster than wood. If there is no way out and you have to fasten it from the outside, be sure to bury the metal caps in a secret place.
• There should be a gap of at least 1 cm between the planks of all elements of the flooring of the bench seats.

The sides of steam room shelves, made in accordance with Finnish sauna rules, are made with ventilation gaps by analogy with the technology for constructing the entire flooring. However, in Russian bathhouses the sides were sewn up tightly with boards to reduce the cubic meters of space heated by wasted steam. Of course, a steam room reduced by this method will heat up faster, but the wood of the floor and wall decoration hidden under the furniture will also dry out worse. The owner will choose what is more practical.

There are no special tricks in how to make a bathhouse bench or shelves for a bathhouse. The shop will be the same in Africa. The main thing is not to forget about the peculiarities of constructing a multi-stage bath structure and get down to business responsibly.

Bathroom wall shelf for accessories

This type of bath accessories is located along the wall and attached directly to it.

Shelves in the bathhouse, made independently:

Glass shelves

The use of glass helps to visually enlarge the space. But in a bathhouse this can be quite dangerous. The ideal option is only to use it in the rest room or kitchenette, if there is one in the bathhouse.

Made from MDF or plywood

There are 2 types of plywood: moisture-resistant and water-resistant. It all depends on the impregnation, which allows it to resist direct exposure to water or high humidity.

How to make a shelf with your own hands from wood

To make a bathhouse shelf with your own hands, you need the following materials:

1. Electric jigsaw.
2. Hammer.
3. Screwdriver.
4. Hand-held circular saw for longitudinal cutting of workpieces.
5. Wood saw.
6. Square and ruler.
7. Varnish for wood.
8. Brush.
9. PVA glue for wood.

It is necessary to take planed boards that are treated with abrasive sandpaper. How to make wall shelves for a bathhouse with your own hands:

1. Dowels need to be installed. They must be installed in such a way that part of the dowels protrudes up to 10 mm.
2. We install and glue the side and main part of the shelves. The ends of the dowels should be well glued with PVA glue. Without waiting for the glue to dry, attach the product to the back wall.
3. Make sure that the shelf in the bathhouse is attached smoothly and secure it with self-tapping screws.
4. Apply varnish to the surface, leave for 12 hours, then repeat again.

The photo shows self-made shelves in the bathhouse, including corner ones:

The path to the heights of art

Also, for applied purposes, crafts are often created from wooden sticks. These things are usually made for convenience. For example, a bookmark.

A face made of colored paper is glued onto a wooden ice cream stick. And the bookmark is ready.

Wooden sticks are also used in flower pots as tags with numbers or inscriptions. But there is another use. Sometimes a whole house is built from sticks.

If you have a lot of ice cream sticks in stock, building a house out of them is a useful fun for kids. Working with ice cream sticks and matches helps children develop their fingers.

Building a house from these materials is not an easy task. This requires precision movements. Of course, in both cases the house is built using glue. It is built in layers, gradually.

One row of the walls of the house has dried up, another is being completed. And so on to the top of the walls. And then the roof needs to be laid there. It takes a long time to build a house. There are beautiful works of art here. There are people who can make masterpieces out of ordinary things.

Bath equipment

How to make wooden products for a bath? If you choose your bath equipment wisely, you can maximize your pleasure from bathing procedures.

The main element in the steam room is a ladle; it is used to add water. You can add herbal infusion to the water or drip kvass onto hot stones. It is mainly made of wood or plastic.

How to make cooperage products for a bathhouse with your own hands? Now let's move on to considering the pelvis and tub. They are usually used for steaming brooms. The basin can be used from any material, but the tub should only be made of wood.

I would like to note such an element as a gang, it is mainly used for steaming a broom, or it is used for washing the body. Typically, such an accessory is made of oak.

Fans of extreme sensations like to install a bucket-waterfall in their baths. Usually a steamed person comes out of the steam room and pulls the rope, at which point he is doused with ice water. Such buckets reach volumes of up to 30 liters.

We suggest you read: Which stones are best to choose for a bath - jadeite, jade and other types, their pros and cons, comparison

Washcloths

There is a wide range of sets of bath accessories, which include brushes, washcloths, peeling stones, etc. If you want an original product that satisfies all your preferences, make it yourself.

A washcloth is necessary for body cleansing and wet massage. This procedure is not only pleasant, but also beneficial for the body. Sponges can be of different hardness, sizes and shapes. You need to choose a washcloth based on your personal tastes.

To knit a washcloth from natural materials, choose the wool of goats, sheep or any other farm animals. You can also use linen. The yarn for the washcloth must be thick, since the product itself is subject to mechanical stress, so choose the appropriate size of knitting needles or hook.

DIY bath furniture

When the decoration of the bathhouse is completed, you just need to furnish it with furniture. Interior items in a bathhouse, and especially in a steam room, should be thought out to the smallest detail. You should not bring old furniture from your apartment here. It is better to deal with the situation carefully. The choice of various items for baths in stores today is simply huge. However, prices can be prohibitive.

In this article we will tell you how to make furniture for a bathhouse with your own hands from wood and scrap materials, show diagrams, drawings, photos and video instructions.

Headrest

On the one hand, the headrest helps you lie down in the bathhouse, and on the other hand, when you relax the muscles, the cervical spine can be stretched well.

The headrest for a bath is necessarily made of wood and can be rounded, straight or curved. Before you start work, you need to make drawings. How to make a headrest for a bathhouse with your own hands:

1. Make 2 rectangles from a wooden blank, 25 mm thick and 1 cm high. The height of the first edge should be 10 cm, and the second – 2 cm. The marks should be connected to each other by a rounded smooth line. Sand the edges of the sidewalls with a grinder and carefully smooth out all roughness and unevenness.
2. It is necessary to cut the slats into pieces of the required length. You need to determine the width of a person’s shoulders and make a headrest of that width. Using a hacksaw, cut off the required number of pieces. Then sand the edges with sandpaper. The surface must be absolutely smooth.
3. You need to assemble the structure. Holes are drilled at the ends of the sides and the slats are screwed on. They can leave burns on the skin, so you should be careful when handling them. Leave small gaps for air and moisture circulation.

To make a headrest for a bathhouse, it is advisable to choose hardwood, which has low thermal conductivity and a loose structure; it will allow it to quickly dry out from moisture.

How to make a bucket?

A wooden panel for a bath is made as follows. Wood carving is mainly done to decorate tables and chairs. But another interesting element is considered a wooden panel, which can usually be found in recreation rooms. Before you decide to make such a panel, try to first decide on a pattern. True, you can find a ready-made drawing or develop it yourself.

The most popular is a panel or sign that depicts a bathhouse attendant with equipment. But another popular option is a sign with the inscription “To wash in the bathhouse - to be born again” or “The fragrant steam heals not only the body, but also the soul.”

Such a panel with a picture or a sign with an inscription can be bought in a store or from people involved in wood carving, but the option of making it yourself cannot be ruled out.

Materials and tools:

• beam;
• sharp knife;
• pens;
• galvanized fastenings;
• stain;
• turpentine;
• linseed oil.

In such cases, you can choose any tree. To manufacture such accessories, work is performed sequentially, namely:

1. We take a block and begin to grind it from the inside.
2. After the sanding process has been completed, you need to use a knife to cut out the design.
3. After the drawing is ready, we cover its cut out elements with water stain.
4. We treat the rest of the part with a solution of linseed oil and turpentine.
5. The last step is nailing the galvanized fasteners.

Any bathhouse should have a wooden bucket. You can buy it on the market or make it yourself.

• wood;
• plane;
• metal hoop;
• pen;
• rope.

Watchmaking craftsmanship

Many bath procedures are strictly regulated by time. For example, people with different levels of thermal hardening are allowed to stay in the steam room for no longer than certain periods. Therefore, a bathhouse simply cannot do without a wall clock, which will be clearly visible from anywhere in the rest room (after all, you also need to rest for a certain period).

In an aesthetically designed bathhouse, everything should be beautiful, and the clock is no exception. You can make original “chimes” with your own hands without spending a lot of time and money on their creation. All you need to purchase is a clock mechanism, which is sold at any craft and hobby store.

For example, you can build a wall clock from several square-shaped pieces of wood. In one section you need to drill a hole in order to attach the clock mechanism through it on the back side, and attach the hands on the front side. It is best to assemble a structure of nine elements, fastening them together into one large square of 3 by 3 elements. Glue them together using epoxy glue. Nails will help to mark the hours on such a dial. Arrange them in a circle, using only four numbers: 12, 3, 6 and 9.

Another clock can be made from an old wooden tub. Drill a hole in the center of the bottom and attach a clock mechanism with hands. Create a clock face at your own discretion and hang this design on the wall.

The clock can also be constructed from several wooden slats. For example, for a hexagonal clock you will need 11 slats. Two of them will be located on the back side, and 9 slats of different sizes need to be nailed to them, which will form a hexagonal shape. Drill a hole in the central rail and thread the clock mechanism through. Watch how to do this in a short video.

Organize the dial using nails. Moreover, if you use old and rusty nails, the design of the product will only benefit from this. It will acquire a now fashionable touch of antiquity.

Another simple method for creating a wall clock for a bathhouse with your own hands involves using a cut from a large tree. This craft will look very laconic and at the same time stylish. The numbers on the cut can be burned out with a burner, or you can do without a dial at all.

Decorating bath rooms will require a fair amount of ingenuity and a sense of taste from you, but the result will allow you to be known as a skillful person who was able to create unique crafts from scrap materials with his own hands. Some of the products do not require great skills and even children can be involved in their production to introduce them to an interesting hobby.

Many bathhouse decor options do not require large financial outlays, and they will look as if they cost a fortune.

Bath furniture drawings

You can make simple wooden furniture for a bathhouse with your own hands, buy more serious products in a store, you can find the manufacturer’s contacts and buy from him at a lower price (although not a fact) or order a set made to your taste.

Wooden furniture from the manufacturer is, of course, good, but if you built a bathhouse yourself, then you can make furniture: the models are not the most complex, there are many available diagrams and drawings. The most important thing is to carefully process the workpieces: the edges must be rounded, all parts must be carefully sanded, first with a grinding machine, then with fine sandpaper by hand until a perfectly smooth surface without the slightest chips, burrs or other flaws.

Bath bench. DIY drawing

The parts are fastened either the old fashioned way using oak wedges, for which the corresponding grooves are cut out (a complex option that requires experience and time), or using self-tapping screws (nails are less reliable). When assembling bath furniture with your own hands using screws, “recess” the caps to a depth of 5-6 mm. Then fill the resulting holes with wood putty of the appropriate color. With this you kill two birds with one stone: the putty protects the iron from oxidation and dark spots and streaks will not appear on the furniture; moreover, if the items are used for the steam room, the metal parts will not burn the skin.

Do-it-yourself wooden bath table: drawing and dimensions (can be changed proportionally)

The table must be in the rest room. At least small. You need to drink a lot in the sauna. You will need to display teas, infusions and cups/thermoses/saucers. So without a table - nowhere. A drawing of a table that is stable and easy to manufacture is shown in the figure above. There shouldn't be any difficulties. The main connections are self-tapping. Their length is 3/4 of the total thickness of the parts being connected (so that they do not stick out from the tabletop). The diameters are all there, where to screw in is marked. Give it a try. It will work out for sure.

There is one little secret that will make the putty almost invisible: add a little dust to it, which is obtained during sanding. If you have successfully chosen the color, then after this additive the marks after sanding are barely noticeable.

Wooden jumping bench. Can be used for a washroom or rest room in a bathhouse. Easy to make yourself

When assembling shelves for the steam room, benches, tables or other bath furniture, place the boards not closely, but with a small gap. This, firstly, will solve the problem of water drainage - it will flow into the cracks, secondly, the wood will be better ventilated, and thirdly, wood tends to expand/contract with changes in temperature and humidity, and such cracks provide the wood with this opportunity.

Conclusions : furniture for baths and saunas should be made of wood. What furniture to buy for a bath is your choice, which depends on taste, habits and capabilities. You can buy a ready-made set, you can order production from a master, or you can try to make it yourself. Any option has its positive and negative aspects, but the most inexpensive furniture for a bathhouse is obtained if you make it yourself. The only thing that can be used with restrictions in the bathhouse is upholstered furniture. In this case, you need an ideal ventilation system that will effectively remove excess moisture from the air.

Selecting materials

First, we need to decide what material we will make bath accessories from, because this place has special conditions, in particular, high humidity.

Exotic

Abashi is a wood that is ideal for creating sauna furniture. It grows in Africa. In addition, abashi always maintains human body temperature. This tree initially has a milky color, but after all the work is done it turns dark brown. The only “minus” is the high price.

Conifers

Wood that contains a large amount of resin can cause burns. When heated, you can not only damage the skin, but also get additionally stained with resin. You can, of course, deresinate pine, but this cannot be done at home. Therefore, it is advisable to give preference to deciduous trees.

You can use cedar for a bath. The wood produced is one of the best, but many buyers are frightened by the fairly high price. Additionally, cedar releases essential oils into the air. They are an excellent disinfectant and deodorant.

Deciduous trees

In most cases, linden and aspen are used to make wooden products in the bathhouse. They practically do not change at high humidity. Over time, the aspen darkens. Gradually, the material may become thinner and scuffs and dents may appear on the furniture.

But linden also has a very pleasant smell, and its soft wood is easy and simple to process. But this is a short-lived material. It is often affected by fungus, and it is impossible to fight them without chemicals.

Furniture for locker rooms and rest rooms can be made of any material. The furniture in the washing room should be able to withstand humidity well.

Useful video about bath accessories:

How to make a bath hanger?

• tree;
• plywood;
• wooden hooks, handles;
• drill;
• saw;
• sandpaper.

Arriving at any bathhouse, you need to undress, and the question arises: where to put things? That’s why a hanger will become indispensable in such a situation, since an ordinary wardrobe for things will look unaesthetic. The optimal solution is a wall hanger, and to make it yourself, you do not need any additional skills:

1. First you need to make a template, which we will then transfer to the boards. If you plan to make several of these hangers, then it is best to make the template not from paper, but from plywood.
2. Now we make markings for the hooks and drill holes. Additionally, make holes for mounting on the wall.
3. Saw the blanks to assemble the base of the hanger.
4. Make or buy wooden hooks.
5. You need to sharpen the edges with sandpaper.
6. Now you can start assembling the hanger and attaching it to the wall.

Mosaic crafts for the soul

Surely there is a place in your dacha or garden plot, in the house or on the street, or in a gazebo, that you want to somehow decorate, but at the same time do it in an unusual way. We offer to decorate any surface with crafts in eco-style. The essence of the method is to lay absolutely any pattern or image from wood cuts of different sizes. We will need:

• Plywood sheet;
• Liquid Nails;
• Varnish;
• Jigsaw or hacksaw;
• Many thin cuts of different sizes.

First, come up with a drawing that will delight you and lift your spirits with its appearance. Now you need to transfer the sketch from paper to a sheet of plywood, following the scale. When the drawing is ready, attach it to the attachment point and estimate the size. Perhaps the craft will turn out to be too bulky or, conversely, so small that it will get lost against the background of a long wall. This can be fixed at this stage. After adjustments, you can begin cutting out the plywood base. Now all that remains is to glue the wooden circles with glue and enjoy your creation.

protect the craft with clear varnish

If you have an old mirror at your dacha, you can use the same principle to frame it in a beautiful frame. The mirror must be glued in the center to a sheet of plywood, leaving the edges free for attaching saw cuts. Usually, if the mirror has a round shape, then the frame follows its contour. And you try to use the opposite method - enclose a round mirror in a square frame and see how unusual it becomes after its transformation.

Bath sign

A great idea among accessories for baths and saunas that are easy to make yourself is a sign. You can do a very interesting option with your own hands:

1. First you need to select a board. It can be attached inside and outside. You should purchase it in a special store. Saw the board into three parts. You can make it some unusual shape.
2. Using a regular pencil, draw oak leaves and write an inscription.
3. Now we should move on to the carving process. After the product has acquired volume, you need to sand the carved surface.
4. The last step is to apply stain and varnish. Apply the stain carefully with a brush. After a while, apply a second layer. After drying, you need to remove the excess.

Spray the varnish at a distance of 10-15 cm. The bath sign will become shiny. Leave it to dry for 12 hours. All that remains is to attach it to the right place.

Drawings, signs for the bathhouse:

Inscriptions, funny pictures for the bath:

And here is a photo of a panel for a wooden bath:

Choosing the direction of the fibers when placing boards on the wall

First you need to lay out the decorative elements on the floor, figuring out how they will look best. Below are all three possible options.

Vertical direction of fibers PHOTO: youtube.com

All boards are placed so that the fibers are horizontal PHOTO: youtube.com

Alternating direction of fibers PHOTO: youtube.com

Probably the best option would be the third one with alternating fiber direction. It looks much more interesting. And for greater contrast, you need to add black spots to this chaotic arrangement. For example, if you combine oak elements with structural burnt ones, you can get a pretty impressive result.

This kind of beauty can appear on the wall PHOTO: youtube.com

Aroma oils

In addition, remember to moisturize your skin. After all, any massage is stressful for the skin, in this case aromatic oils come to the rescue.

We invite you to familiarize yourself with: Electric sauna stove, electric stove and electric sauna heater for 220V, Sawo stove and Harvia heater

They are also used to make the air in the steam room more pleasant. For these purposes, it is enough to add a couple of drops to the stones. The calculation is as follows: use 10 drops per 1.5 liters of water.

For healthy relaxation, it is important to use aromatic oils; their benefits are explained by their disinfectant properties. A set of plant extracts such as ginger, lavender, fir lifts your mood and vitality.

Features, types of metal and brick stoves

Simple in shape, metal sauna stoves may differ slightly in design. The classic, easiest to make option is the potbelly stove. Essentially it is a metal box with a door and a pipe. However, this form is considered uneconomical: fuel consumption is high and heat transfer is low. The thickness of the metal for a modern, more economical type of sauna stove should not be too large, the optimal one is 4-5 mm.

Some owners make a combined stove for their bathhouse, the core of which consists of metal sheets, and the outside of the structure is lined with bricks. Thus, they achieve a reduction in fire hazard and an improvement in the uniformity of heating of the surrounding air. The basis for installing such a furnace can be a concrete slab lined with ceramic tiles, refractory bricks or a metal sheet.

Among the small variety of types of metal sauna stoves, three main types stand out: closed, open and combined stoves. The first type is distinguished by a completely closed combustion zone and small size. Open stoves contain in their design places for laying out heating stones that do not close.

Closed oven Source tildacdn.com

Typically, the firebox of a homemade iron stove for a bath is placed in the waiting room, and the part with heating stones is located directly in the steam room. To properly operate an open stove, it is necessary to ensure maximum contact of stones with the outer surface of the firebox.

As for combination stoves, they have the additional ability to heat the air in the room. This can be done by equipping the structure with a network of pipes, which are attached to the stove through a pipe and are then brought out so that they cover the entire perimeter of the bathhouse complex. When the fuel in the stove burns, the energy generated heats the air, after which it begins to circulate through the pipe system. In this case, the supply of heated air is carried out by moving a special grille in the form of a valve.

Brick stoves themselves are safer than metal stoves, and also more convenient. The reason lies in the gradual and uniform heating of the air surrounding the stove. The location for the construction of such a stove must be chosen carefully. The heating element should be located near the wall of the room, but no closer than twenty centimeters from it.

Brick oven Source wmpics.pics

See also: Catalog of companies that specialize in the design and installation of fireplaces and stoves

Helpful information

Traditionally, homemade sauna stoves are built from brick.
This material is able to heat up evenly and release heat slowly, which is important for the formation of healing steam. If the steam room has a small area, they try to place the entire structure in the washing room, and only the side of the stove is brought into the steam room

Simpler stove designs are made of metal. A universal option is ovens that use both brick and metal.

There must be a gap between the stove and the wall (as well as any other wooden bath structure). For a brick stove this distance is 30-40 cm, for a metal stove (lined with brick) - 60-70 cm, for a metal stove or metal pipe -100 cm.

The above distances can only be reduced if the walls or other wooden structures that are in close proximity to the stove are protected from accidental fire by foil with asbestos cardboard.

Homemade stove made from a metal pipe: layout of structural elements.

A homemade stove is made of ordinary bricks. Hole, slot and sand-lime bricks should not be used, since they do not provide uniform heating and quickly collapse under the influence of high temperatures. Poorly fired bricks are also not used. You can take used bricks if they are strong enough and there are no chips or cracks on them. Usually these are bricks from old dismantled walls and stoves. Before use, it is cleaned of solution and soot.

The size of the brick that can be used must correspond to 250x120x65 mm

It is very important that all its corners and edges are straight, the shape is correct, and various defects are absent. Most often, a homemade stove in a bathhouse is lined with bricks of grade 75-150 with a density of 1700-1850 kg/m³ and a weight of 3.6-3.8 kg

High-quality fired brick produces a ringing sound when tapped.

From the pipe

If there is space to install a stove, you can make a homemade electric stove from an iron pipe and U-shaped industrial electric heaters. The following is recommended:

• select the pipe diameter according to the size of the electric heaters;
• place the heaters in one of the pipe holes with the contacts facing outward, make grooves around the perimeter of the hole for inserting ceramic bushings for wires connected to the electric heaters;
• close the pipe hole with a durable metal sheet, which will become the base of the stove;
• connect the sheet to the pipe;
• the connection can be either welded or threaded;
• the free space of a vertically standing pipe must be filled with basalt-type stones measuring 6–11 cm.

Stones at the bottom of the pipe should not put pressure on the electric heaters.
To do this, you can place reinforcement rods along the pipe between the electric heaters, which will become a supporting device for the stones. The pipe and support sheet must be grounded. That’s it, the smallest stove-heater for a mini-sauna is ready. All that remains is to make the correct connection to the network and grounding device. Stoves with a power of up to seven kilowatts are connected to a 220-volt network, more powerful ones are connected to a 380-volt network. The same design can be used to construct a stove in a fairly large bathhouse. A large diameter and length of pipe and a larger number of electric heaters should be used. Date: September 25, 2022

Room interior

There is no more suitable place where you can simultaneously relax after a busy work week, imbue yourself with harmony, and cleanse your body than a sauna or bathhouse, which is closer in spirit to the Russian spirit.

For many, visiting it is a tradition that is supported by every generation, and is often instilled in families from early childhood, so it is not surprising that our compatriots want to have their own bathhouse in the backyard.

Great place to relax

The environment inside should give harmony and tranquility. This atmosphere is achieved by the combination of all parts of the interior. You should not think that the type of Russian baths is a standard steam room with a stove and the same type of shelves. A designer interior is always distinguished by original details and decor; only by implementing an individual project can you get a stylish room for couples and relaxation.

Stylish room in oriental style with your own hands

Quality, thoughtful finishing and accompanying accessories are three pillars of internal content that will never cause you any inconvenience. For information on how to equip the interior, I will tell you today. These ideas can be used both at home, for your own needs, and for business.

Thoughtful finishing is the key to success

Best Ideas for small, narrow, cramped, corner corridors and ways to turn them into a comfortable Hallway (200+ Photos)