DIY feeder chair, detailed guide with photos and videos

Fans of fishing know that enjoying this process will be much more enjoyable if you take special equipment with you to the pond. The feeder chair serves exactly this purpose - creating a more comfortable environment. There are many options for such chairs in stores, many of them are quite expensive. To save your family budget, you can make a feeder chair with your own hands that fully meets the fisherman’s requirements. This is not difficult to do, you just need to prepare the necessary tools and carefully measure all the parts.

What is

A chair for feeder fishing can be made in the form of a simple stool. For greater comfort, it is worth building it more complex: with a back, armrests and a body kit. For a chair to be comfortable to use, it must meet the following requirements:

Compact design - the chair should easily fit into a backpack when going fishing.
Lightweight, which is important for carrying over long distances.
Strength, which affects the ability to support the weight of the fisherman.
Stability on any surface, since the banks of reservoirs are not perfectly smooth. The safety of the fisherman depends on this.

The legs of a chair for winter fishing should not be thin so as not to be pressed into soft ground or snow under the weight of a person. Another advantage of the feeder chair can be the adjustable back and legs, which allows you to change the height of the backrest and, in a sitting position, relieve tension from the back that arises from being in one position for a long time.

Compact design

Lightness

Strength

Stability on any surface

Primary requirements

Interesting fishing spots are often located in very inaccessible regions and remote from civilization. This imposes certain additional requirements on all equipment. And city fishing, in the absence of a personal vehicle, forces you to be more careful in choosing gear and additional equipment.

Read Fish Shamayka

Typically, homemade fishing chairs, chairs and platforms require:

Sufficient strength. Tourist and fishing furniture must have a sufficient margin of safety in order to withstand the weight of the owner and additional body kit. And it should also be taken into account that the load increases significantly at the time of casting.
Sustainability. Fishing places are rarely convenient for the arrangement of chairs or armchairs. And when fishing and recasting, the unstable structure can simply fall back or to one side. Sand, clay soil, viscous silt, stones and other options require stability, as well as, ideally, adjustable length of the legs, which will allow you to set your place exactly, regardless of the terrain.
As compact as possible in transport position. The space in the trunk of a car is not unlimited, and if you do not have your own vehicle and you have to use public transport to get to the fishing point, then this parameter becomes even more important.
As little mass as possible. This parameter does not fit well with the requirements for the greatest possible strength, since the only way out is to use lighter materials, which sometimes comes at the expense of strength characteristics.
Availability of materials. If you need to buy only a few parts in a hardware or other store to make a chair or armchair, that’s one thing, but it’s a completely different matter if you need to buy all the materials and tools for the job. In the latter case, a more rational solution would be to buy a ready-made chair in a fishing store.
Ease of manufacture. If the design requires any special, advanced skills in working with wood or metals, then this is not the most suitable option. Ideally, such furniture should be made in a few hours.

Important! The sizes of chairs or armchairs must be selected taking into account the volume of possible clothing. Few people limit themselves only to summer fishing, and fishing in the fall or spring often requires more than one layer of warm clothing

Tourist and fishing furniture must take into account the possibility of accommodating such additional volume.

Varieties of design

There are several types of do-it-yourself fishing chair, which is determined by its design features:

Folding chair - consists of a seat and backrest connected by a hinge.
Armchair with backrest. Models of this design are either solid or folding. A folding fishing chair is more mobile and can easily fit in a backpack, while a solid product is considered more durable.
Lounge chair. Chairs of this design, in turn, are divided into prefabricated, solid, and folding.
Armchair with shelves. The main feature of the model is special devices for placing gear and other fishing accessories on it.

The easiest option to make with your own hands is a folding bed; it can be made from any materials with the least amount of money and time; a lounge chair is a more complex design.

When choosing a device, you should take into account your strengths and, if you do not have skills in making feeder chairs, start assembling with the simplest variety.

Cot

With backrest

Sun lounger

With shelves

Recommendations

Many fishermen practice making various accessories with their own hands. Firstly, it is interesting, and secondly, this approach allows you to save significant money. If you buy a chair for a fisherman, even the simplest one, you will have to part with a certain amount of money, and a considerable one.

But if you have extra funds, and do not have the desire or skills to make at least a basic product with your own hands, then you can go to a fishing store and buy any chair you like. As a rule, the store always has a wide range of similar products that can satisfy any category of consumer. Here you can buy both a simple folding chair and an armchair with armrests: if only you had the money.

Igor 03/11/2018

Manufacturing materials

The main materials for assembling a feeder chair with your own hands are the following:

Wood or chipboard. Wooden products must be impregnated with special agents that increase moisture resistance, otherwise the chair will not last long and will quickly begin to rot under the influence of water.
Steel. A chair made of this material is the most durable, provided that it has been treated with an anti-corrosion compound, since rust will appear on the metal over time when exposed to moisture. To make a fishing chair from steel, you will need a more complex tool.
Polypropylene pipes. Material that does not require special processing. Stools made from it are quite strong and durable. Assembly is easy; simple tools are required.
Textile material. For the manufacture of seats and backs, it is better to choose more wear-resistant textiles, for example, tarpaulin, which will not tear upon first use.

When making a chair for feeder fishing, it is not recommended to choose plastic or aluminum - such materials are quite fragile and unreliable. The product will not last long, especially if such chairs are used by people with a large weight.

Tree

Polypropylene pipes

Steel frame with textile seat

Plastic fishing stool

Since wood is extremely afraid of water, some prefer to use another material - almost weightless plastic, which, moreover, does not tolerate any moisture. To build a lightweight structure you need to prepare:

pieces of plastic pipes - 4 x 350 mm, the same number of 500 mm;
plastic corners;
thick fabric;
fastening: bolts with nuts.

Long elements are connected in pairs in the middle crosswise using bolts. They are not tightened tightly, otherwise the structure will be difficult to fold. Corners are attached to the ends of the tubes, into which short elements are then inserted.

After receiving the frame, a piece of suitable size is cut out of the material for the seat. It is sewn on a machine, the seat is put on the upper elements, dismantling one of the sides. To secure the legs, a narrow strip of the same fabric is sewn at the bottom. Those who wish can also provide it with a backrest, making it in the same way. It is rigidly mounted to the top of the stool - to the frame of the front legs. The chair is made from metal pipes in the same way.

How to make a drawing

The first step in creating a fishing chair with your own hands is to complete the drawing. There is a diagram of any chair on the Internet. As a rule, these are drawings of simple structures. More advanced models with additional devices can be drawn with your own hands. Another way to make a drawing is with computer programs.

When choosing the dimensions of a feeder chair - seat width, height of legs and backrest - you should take into account the build of the fisherman who will use it. This will help make your fishing stay more comfortable. For a fisherman of average build, the optimal parameters are considered to be 1.5 x 0.5 m.

If, when making a fishing chair with your own hands, the drawings do not match the width and height parameters, you can safely change them to those that will be optimal.

Fishing stool

Fishing chair with backrest

DIY feeder chair. Part 1

Having seen it one day at a neighbor's place on the ice, an ice fishing enthusiast becomes eager to have his own comfortable feeder chair. But the cost of even the simplest seats for winter fishing in ruble terms is now so substantial (from 7,000 rubles without body kit!) that if a person does not have a significant amount of free money, it is impossible to justify the purchase by any catches or desire for convenience.

Tools in your hands!

It is quite possible to get a comfortable and reliable seat for feeder fishing without breaking another hole in the family budget - you can make it yourself at home. To perform this work, no special skills of a locksmith or a master of sewing on a sewing machine are required.

Everything can be done by a person with average abilities to design and make something; all he needs to do is be determined and stubborn.

After the design of the fishing chair has been thought out, the necessary sketches and outlines have been made, it is necessary to calculate the amount of materials.

If the dimensions of the product are approximately one and a half meters in height and half a meter in width, then you will need materials that can partly be bought in a store, and partly found at home.

It is difficult to choose a more suitable material for the frame of a future chair than a profile pipe. The main advantages of this material:

cheapness;
high strength;
weldability;
ease of machining.

Necessary materials

Materials from which most homemade feeder chairs of simple designs are made:

pieces of plywood 8 mm thick;
steel pipes with a diameter of 20-25 mm with walls whose thickness is not less than 1.5 mm, cutting elements from these pipes for one chair will be: 55 cm - 4 pieces, 70 cm - 2 pieces, 30 cm - 1 piece;
pieces of fabric with foam padding for covering the seat and back: 800x400 mm – 1 piece; 700x400 mm – 1 piece;
bolts with nuts and wings of various lengths for assembling legs, seat and back;
furniture bolts for connecting the seat to the back;
steel plate for thrust bearings 3 mm thick;
staples for a construction stapler 6 mm;
primer and dye for processing the chair frame - in the minimum volume available on the sales counter.

For the feeder, the size of the seat-chair of the universal version is almost the same - 1.5x0.5 m. The given quantities and sizes of elements are based on a simple version without side armrests and an additional shelf for the legs.

If the craftsman considers these elements of the chair to be useful, then he will additionally need the materials of the listed nomenclature, but in a different quantity. Drawings of do-it-yourself corrugated pipe seats can be found in abundance on fishing equipment websites.

Foldable design

One of the most successful designs is a feeder chair with insulated foam upholstery. To stick foam rubber onto plywood, you will need titanium glue, and it is more convenient to prime and paint the finished frame using spray cans. It is better to choose a matte black paint color.

An important detail is that the chair for winter fishing must be foldable, since it will constantly have to be transported, carried, moved every time you go fishing.

It is permissible to make all frame elements from a round aluminum pipe of sufficient strength, in which case the chair will be much lighter. But welding aluminum at home is problematic.

Popular search queries for video clips on the Internet are: “Do-it-yourself feeder chair”, “Make your own feeder chair”, “Chair for a winter feeder”.

Manufacturing stages

Taking into account your own skills in making products from different materials, as well as personal wishes, you can build your own chairs for feeder fishing of varying complexity.

Simple model

To make the simplest model of a feeder chair, you will need three interlocking metal pipes with a diameter of 20 mm, material for the seat and back, strong threads, 4 bolts and nuts. Necessary tools: electric drill, hacksaw, grinder. Manufacturing technology:

The short sides of the seat are stitched with two wide strips and secured at the bottom with a limiter made of a thin strip. In this case, the fabric is sewn directly onto 2 metal pipes, which will serve as the legs of the chair. The material on the back is also stitched along the short sides.
At the junction of the legs, holes are drilled in the middle of the long sides and connected crosswise to the fasteners.
A pipe is attached to one of the legs, which will serve as a backrest.

It is worth considering that in this design the backrest does not fold.

With adjustable legs and backrest

A chair with a back is a more complicated version of a feeder chair. Material required to assemble such a chair: steel pipe for the frame with a diameter of 20 mm, fastenings (bolts, nuts), textiles for the seat and back, threads, rubber nozzles for the legs, anti-corrosion compound. The tools used are the same as for the simple model. Assembly algorithm:

The metal pipe is cut into several parts: for the legs and seat - 8 pieces of 55 cm, for the back - two pieces of 70 cm, one piece - 30 cm.
On two pipes, which are intended for sitting, two fasteners are installed at a distance of 6 cm from the beginning and end.
Another fastener is attached to one of these pipes, with which the back will be mounted. The fastener is located at a distance of 9 cm from the beginning of the pipe.
To complete the manufacture of the chair frame, the prepared corrugated pipes with fasteners are connected by two more pipes. Thus, 4 metal pieces measuring 55 cm were used.
Pipes measuring 70 cm prepared for the backrest are connected to a pipe 30 cm long using fasteners.
The remaining four 55 cm pieces, which will serve as legs, are attached to the ends of the frame tubes. They are equipped with rubber nozzles.
At the last stage of making the chair, textiles are stretched over the seat and back. Holes are made on the short sides of the tarpaulin, and the material is pulled together using an elastic band. The elastic will allow the seat to sag a little under the weight of the angler. The back textile is pulled together along the long sides.

The described design will allow you to adjust the legs in height, which will make the chair more convenient to use.

Made from polypropylene pipes

A simple option for making a feeder chair, for which you will need: PVC pipes with a diameter of 25-32 mm, fittings connecting the parts of the chair, durable textiles for the seat, fasteners, threads. Tools for assembly: pipe cutting scissors or a hacksaw, soldering iron. A guide on how to make a fishing chair from polypropylene pipes with your own hands:

The tube is cut into pieces: 16 parts for the back, legs, and seat, the length of which you can choose yourself.
We connect the pipe sections with fittings. For convenience, assembly should begin from the back, then the seat and handles are fastened together.
For the seat and back, take material that is stitched along the short sides with holes for inserting pipes.
After checking the structure for stability, it is disassembled, the material is stretched onto the appropriate sections of pipes.
At the final stage of assembly, the parts are soldered or secured with glue.

The result is a homemade chair with armrests that will be quite stable on any surface. It is worth noting that the back of such a design does not move, its position remains unchanged.

Folding chair

To assemble a folding chair, you will need a polypropylene pipe with a diameter of 25 mm, fittings, material for the seat, threads, 2 bolts, 2 nuts. Guide on how to make a folding chair:

The fabric is cut to a size of 18 cm. It is stitched along the short sides so as to create holes into which the pipes will be inserted.
The pipe is cut into pieces: 4 pieces of 40 cm and 4 pieces of 20 cm.
Long pipes have holes drilled in the middle for bolting.
Short 20 cm sections of pipe are inserted into the prepared fabric. Corners are put on the ends.
2 rectangles are formed from all pipe sections measuring 20 x 40 cm. They must be connected with fabric.
The rectangles are connected to each other with bolts and nuts in the drilled places. It is not recommended to tighten the nuts too tightly so that the chair folds effortlessly.

For structural strength, glue or welding can be used in the places where the fittings are attached. This folding fishing chair will serve for a long time thanks to the material from which it is made, it will be easy to carry, and the chair will not take up much space in your backpack.

Tools

In the process of making and assembling a wooden fishing chair, you will need the following tools:

drill;
screwdriver;
hacksaw;
English keys;
scissors for working with fabric;
sandpaper.

Materials that will be useful:

wood;
bolts and nuts;
paints and varnishes;
brushes

Finishing and operation

To increase the service life of a hand-made feeder fishing chair, you need to carry out additional finishing processing of the materials:

A chair made of metal pipes must be treated with an anti-corrosion compound. When using the chair in adverse weather conditions, rust will appear on the metal parts over time, which will shorten its service life.
When making the legs, seat or back of a chair from wood, the surface must be coated with an antiseptic, primer and paint composition. This will significantly increase the resistance of the material to water and also extend the life of the chair.

Proper care is an important condition for the long service life of the feeder chair. After each use, the chair must be put in order: remove any adhering soil, wipe it dry. It is advisable to store the fishing chair in a specially designated place where it will not disturb anyone and will be protected from moisture.

A chair made of metal pipes should be treated with an anti-corrosion compound.

When making parts from wood, cover the surface with an antiseptic, primer and paint composition.

Selection principles

Any chair should be comfortably adjustable. It should have reliable systems for adjusting the chair, legs, and handles. What matters is the time when the fisherman is going to fish.

If the fishing process falls in winter, then you need to make sure that the ice fishing chair stands securely on the surface. It should be smooth and durable.

Very often it is not possible to get to a fishing spot in one or several hours. For this reason, you have to use public transport or walk. In such situations, the size of the chair is important. Universal folding chairs are the right choice.

It is also very important that the weight of the chair is light. Heavy four-legged companions have never added joy to anyone during a hike.

Sometimes the criterion for choosing a chair is its cost. The price of a fishing table can start from 3,000 rubles and end at around 7,000 rubles.

Additional accessories

The simplest model of fishing chair is a stool. Some fishermen consider armrests unnecessary, as they can restrict movement. Store-bought products often have body kits - additional devices that make fishing easier. It’s convenient when everything you need is at hand and you don’t have to bend down to the ground to get bait or tackle. You can also build such devices with your own hands, adding them to a fishing chair.

Materials required to make the body kit:

aluminum pipe with a diameter of 25 mm;
fittings - tees and angles, 4 pieces each;
pipe fasteners;
nuts and bolts;
plastic box or tabletop;
plastic clips for securing the pipe.

Required tool:

electric drill;
soldering iron;
hacksaw for metal;
drill.

Manufacturing technology:

The holes in the fittings are drilled out to 26 mm so that they can be attached to the legs of the chair.
The nut is fixed in the plastic tee so that the bolt holds the aluminum pipe in the fitting. A hole with a diameter of 8 mm is drilled in the tee, in which the bolt is installed.
To obtain a clamp for fixing the pipe inside, the nut is heated with a soldering iron and pressed inside the tee.
To fasten parts of the body kit, which are required occasionally when fishing, additional holes can be drilled in the corner where the bolt and nut are placed. It is recommended to place a washer under the nut to prevent deformation of the metal tubes.
The mount for hanging a box or attachment table is made in the form of a pipe placed on the side of the chair, running parallel. From the central support in the middle, an additional pipe is led to the side in the shape of the letter “T” with a leg in the ground. The table is attached with clips screwed to the bottom.

To attach the fishing rod, no additional support devices are required. It is enough to attach an outlet to the leg of the feeder chair. In the same way, you can make a folding chair with fastenings for other useful devices, fixed with fittings to the legs of the chair.

Fishing backpack chair

A universal model can be considered a model of a backpack with a chair. This backpack will be an ideal companion on any trip.

It is characterized by the reliability of prefabricated fastenings, as well as a universal aluminum frame in the assembly. Such a chair is not only an opportunity to sit comfortably in nature, but also to carry the necessary things over a long distance.

Its mesh pockets can hold everything you need. The fishing line, fishing rod, and bait are placed here. This backpack is a guarantee that your fishing gear will always be at hand.

What is the difference between a winter cot?

If you go online and look at photos of winter fishing beds, you will see that this furniture for fishermen is completely different from country beds.

It is special in that:

Heavier and more massive than other beds;
It is made from durable frost-resistant materials;
The material is much stronger than that of conventional folding beds, and also does not allow moisture to pass through and retains heat;
The durability of such a product is proven by the fact that it is designed to withstand a man in warm clothes;
This folding bed always comes with a warm cover to protect it from frost.

Arrangement of the feeder's workplace

If you have the right equipment, the only thing left for an ice fisherman to do is set up his workplace well. All elements of equipment used for fishing should be located literally at arm's length from a seated person. This will save him from having to get up often, exposing himself to the cold wind and being distracted from the process of fishing.

The main element of the arrangement is the feeder chair. After all, winter fishing is mainly a passive activity - a person has to sit in one position for a long time. At the same time, the load on the back increases, especially on its lumbar region.

Industrial options for feeder fishing chairs

Important accessories for feeder fishing should be at hand: a bucket with bags of dry and home-prepared bait, a box with bait. Not all fishermen are willing to lay out their catch right on the ice at their feet.

Some people, having removed the fish from the hook, immediately put it in a small plastic container or bag. To do this, the container must also be placed near the seat itself, so that the necessary manipulations with the catch can be performed without getting up.

A seat with a folding attachment table and a body kit necessary for winter fishing makes any handling of fish, hook and bait convenient, minimizes time and effort for all auxiliary procedures, making it possible to concentrate only on the main thing - fishing. Even if something suddenly appears in the fisherman’s field of vision, he will not ignore it, while continuing to fish.

A more reliable option for storing individual accessories is in special pockets made in the seat upholstery. This is guaranteed to prevent a sudden gust of wind from blowing away the bait or bait.

In addition, putting all the necessary accessories into the seat pockets and removing all the necessary accessories from there is much more convenient than constantly bending low when everything is laid out on the ice. You can choose any other design of niches and pockets for accessories in the chair, taking into account your individual priorities.

Algorithm

Many fishermen use the following pattern for making a chair:

cut the plastic tube into 8 separate parts. 4 of their parts should be 50 cm long. The rest can be up to 35 cm in size;
A canvas is prepared from a prepared piece of tarpaulin, which then serves as a seat. The other part of the tarpaulin usually serves as a kind of jumper in the design of the high chair. The width and length of these parts are measured in advance;
then you need to connect the two tubes crosswise. All structural elements are secured with bolts;
in the upper area and lower area, the components of the high chair are secured using plastic corners.

Thus, the frame can be called ready. Next, you need to take several pieces of tarpaulin and hang them around the structure.

A thin strip of fabric should be attached to the lower elements of the support. It will serve as an excellent limiter. A homemade model is not only a cheaper option, but also an opportunity to show your creative inclinations.