What can you make from an old blender with your own hands?

Nothing lasts forever, including electrical appliances. Especially electrical appliances. Let's take a hand blender for example. The most common accident is a broken nozzle. Everything else works, but the attachments are broken and cannot be repaired or replaced.

In such a situation, the blender is almost always sent to the graveyard of home appliances. But don’t rush to bury your non-working chopper until you read this article to the end, from it you will learn what you can do with your own hands from an old blender.

Disassemble and understand

The design of the blender may be different, but you still have to disassemble it. Sometimes to do this you need to find a special plug, pry or press on it a little, and the plastic case, not restrained by anything else, breaks into two halves right in your hands.

Other models are held together with screws. Several rotational movements with a screwdriver in the places of the cross-shaped recesses remove the fastening elements, and the parts of the frame are undocked.

Now you need to understand what can be done to restore the life of the device.

How to sew a tiger pillow with your own hands

author Evgenia Vdovina

Great idea to make a big tiger as a pillow! And it’s very simple, for this we just need to find striped fabric, there shouldn’t be any problems with that. It would be nice to take some kind of fur, in general the animal will turn out like a real one.

In addition, you will need filler, eyes and a nose.

How to sew

1. Cut out all the details.
2. We connect the parts of the paws, ears and tail and sew along the dotted line marked on the pattern, turning it inside out. The ears can also be additionally stitched on a machine.
3. Sew the ears to the head. Make sure that when turning them inside out they are on the outside.
4. We connect the head with the body.
5. Now you need to baste the paws and tail to the body along the short sides and stitch the body around the entire perimeter, leaving 10-15 cm for turning.
6. We fill the pillow with padding polyester and sew up the cut.
7. Glue artificial eyes and nose onto the face.

These are such cool pillows!

Rich inner world

Before us is the mechanism of the device: motor, board, wires and everything else. A very common breakdown in many modern electrical appliances is the thermistor. He's a fuse.

If all the fault is in it, then from the blender you can make... a blender! Just replace the fuse with a new one (in accordance with its technical parameters), and your device will live a full life again.

What sauce can be made in a blender: a delicious addition to side dishes

If you are tired of store-bought sauces made from unknown materials, we offer you the ideal option for cold gravies made in a blender.

Mustard Tartar sauce

To make a rich and thick sauce that is ideal for spaghetti, potatoes and shrimp, you will need:

• mustard - 1 tbsp. l.;
• lemon juice - 1 tbsp. l.;
• yolk - 1 pc.;
• vegetable oil - 100 ml;
• pickled cucumbers - 3 pcs.;
• green onions and parsley - several sprigs each;
• salt, pepper - to taste.

Add more grain mustard to get an original and beautiful sauce

Method of preparation: cut the greens into pieces and place in a container. We also send mustard, yolk, seasonings and chopped pickles here. Be sure to add vegetable oil at the very end. Start the blender and blend for 5 minutes.

Details

What will be needed for the remodel? An adapter coupling, a chuck for it, a milling or engraving attachment, or any other - at your request.

All these devices are essentially a drill, that is, a compact rotary instrument with high speeds on the motor shaft. The electric motor of the device rotates the spindle to which the nozzle is attached. It can be cutting, grinding, drilling - there are a lot of options, the tool is universal and its final purpose is determined by the available equipment (attachments) and your imagination.

That is, by repairing your broken blender, you can get several tools in return.

Sunflower seed pate - a healthy breakfast product

The distinctive properties of seeds are the richness of microelements necessary for the body. Let's use a blender to prepare a delicious and very unusual snack that can be eaten both for breakfast and throughout the day.

You will need:

• sunflower seeds - 1 tbsp.;
• basil greens - 30 g;
• lemon juice - from 1/3 of a whole lemon;
• garlic - 1 tooth;
• paprika, salt - to taste;
• parsley - 30 g.

Sunflower seeds are a great boost of energy for the body.

Cooking method:

1. Peel the seeds and soak in cold water for several hours.
2. Then combine the product with the remaining ingredients in a bowl and add to the blender jar.
3. Set the desired speed and grind the mixture until smooth. After the product is ready, it can be eaten.

New life

Let's consider the procedure.

1. First, it is necessary to remove the old coupling - an adapter that connected the drive shaft to the nozzle of the then blender. The easiest way to do this is with pliers. You may have to saw off some elements of the body, now superfluous.
   Read also:  Homemade video surveillance using simple usb webcams.
2. Next, you need to measure the motor shaft (thickness) to know which coupling is suitable. When a suitable coupling is available, it must be placed on the shaft and securely secured using a hex key.

3. It is likely that in order to take measurements and secure the coupling to the shaft, you will need to remove the engine from the housing - do not forget to return it to its place when this work is completed.

4. At this stage, the repair itself, also known as remodeling, is completed. We connect the parts of the case together, insert the plug into the groove, tighten the screws, and put the device into operational condition.

Connecting equipment to pedal control

It is not always convenient to select and manually control the operating speed of new equipment. You can add a pedal to your grinding machine as follows:

• disassemble the body;
• disconnect the electronic control;
• connect the motor directly and make the connection to the pedal.

However, you need to know that not every model is suitable for connecting to a new device. Incorrectly selected equipment will lead to engine overheating and failure. All this can end in a short circuit. It is not difficult to calculate the required power; each product has a label indicating the nominal parameters.

To calculate the optimal pedal load current, you need to divide the mixer motor power by the network voltage. In our case it is:

700 watts / 220 volts = 3 amps.

If the pedal has a factory rated load current higher than 3 amperes, it is quite possible to make such a connection.

This device is suitable for sharpening household knives, meat grinder knives, household tools, and can be used for polishing wooden, plastic or metal objects.

Figure 4 Foot pedal motor control frees your hands

What are you?

You can attach the cartridge to the coupling now or at the previous stage - as is convenient for you. Much more important, what kind of attachment will this cartridge have? That is, what will the updated device be like?

The blender motor is noticeably weaker than the drive of a professional dremel or drill, but for household use, making crafts, and sanding soft surfaces, it is quite enough.

Decide for yourself what you want from this tool right now - for it to cut, polish, or mill? We decided - install the appropriate attachment in the chuck and work for your pleasure. Maybe you want it to be a hand fan? Then you will need to make a nozzle with blades, but that's a completely different story.

Did you like the article? Tell your friends about it:

1 1

Smoothie recipes for weight loss for Blender

This drink option is suitable for those who care about their figure and want to maintain an attractive shape or lose a little weight for the summer season.

A smoothie is a drink with different flavors, so you can add any ingredients to it.

Ingredients:

• low-fat kefir - 1 tbsp.;
• green apple (Simirenko variety is suitable) - 1 pc.;
• kiwi - 1 pc.

Method of preparation: pour kefir into a blender container, peel the kiwi, cut into half circles and immerse in kefir. Wash the apple and remove the seeds, cut it into several parts and put it in a blender. You can also add chopped fresh parsley to the mixture. Start the blender at first speed and gradually increase it. Preparation time is 5-10 minutes, depending on what consistency you want the drink to be.

Using a special tool Blendercleanser

It is recommended to clean the beauty blender with a professional Blendercleanser, which will carefully remove any dirt without disturbing the delicate finely porous structure.

Instructions:

• Apply a couple of drops of liquid to a damp sponge.
• Beat until foamy, kneading vigorously.
• Remove dirt stains with massage movements, rinse with warm water.
• Squeeze out the water thoroughly and leave to dry completely on the small tray included in the kit.
• It is prohibited to use heat devices such as hair dryers, radiators or heaters for drying.

Don't miss the most popular article in the section: Fashionable bangs of the new season for medium, short, long hair. Photo.

How to make a table grinder from a mixer?

You can make a grinder for sharpening knives or other objects only from a running mixer. To do this we need a part of the body with a motor. It is good if it is a stationary instrument with a removable portable flask. The transformation process will occur as follows.

1. Prepare the mixer body, check its operation, as well as switching speed modes. If necessary, repair the electrical part of the equipment.
2. For sharpening tools, a regular grinder disc with a diameter of 125 millimeters is suitable.

Figure 2 A section of 125 mm is quite sufficient for new equipment

If the mixer was initially set to operate at several speeds, all sharpening and polishing must be done at maximum speed. It will be more productive.

Figure 3 Second life for a mixer - a sharpening tool

Collecting Scarlet

There are two types of blenders: submersible and stationary. The first ones in terms of design are handles with choppers, so usually no one has any difficulties with their preparation. The latter are installed on a table, take up more space and consist of a larger number of removable elements.

To learn how to assemble a Scarlet blender, just get acquainted with the assembly principles of one of the most popular models, IS HB44K03. The model has a kitchen processor. If the basic extensions are not enough, you can buy additional rings, just like for other Scarlet blenders.

The set includes 6 attachments:

• cutting into cubes.
• grinding
• whisk
• kneading the dough.
• making puree.
• grater and shredder.

Select any blade you need and begin assembling the IS HB44K03:

1. Install the lid holder into the hole in the center of the selected knife.
2. We place a support rod in the center of the container if expansion requires it.
3. Close the container and turn the holder so that the chopper is fixed.
4. Place the lid on top.
5. Turn it until it fits snugly against the walls.
6. We insert the handle with the electric motor into a special connector.

1. Scarlet IS HB44K03 is ready for use. You can add food for chopping through a special opening. The model can also be used as an immersion blender, for example, if you are going to use a whisk. In this case, it will be enough to attach it directly to the handle in which the Scarlet kitchen processor is located.

Case manufacturing

For the base, a case from an old top-loading washing machine is suitable, namely its outer part, made of stainless steel with a wall thickness of up to 2 mm. During the processing process, the workpiece is cut into four parts, obtaining 2 end and side parts. The elements are folded into one structure and secured with a welding machine. Before the side parts are finally welded, the metal sheets at the bottom are slightly bent, creating a small gap between the rotating shaft and the wall of the structure.

For smooth rotation, the shaft is well secured using bearing units similar to those installed in circular machines. In order for a home-made apple crusher to stand securely, it is attached to a support frame, for the manufacture of which metal corners are used.

For the base of the machine, wooden blanks from durable rock are taken. A plank base is placed at the bottom, on which a container is subsequently placed to receive the processed mass at the outlet, which later needs to be placed under the apple press.

Combined option

Today, lovers of various technical innovations are pleased with the appearance of a universal device - a 2-in-1 blender-mixer. The purchase is very practical because it saves money. By purchasing such a thing, you don’t have to spend money on an additional device. Compactness is the second positive reason. The device will not take up much space in the kitchen. After use, usually periodically, the model is assembled and modestly waits for the next time in its corner. This unit is suitable mainly for small-scale culinary masterpieces.

Nozzle functionality

To increase the functionality of the units, special attachments are used. Some of them are included with the blender, others are sold separately. If necessary, any elements can be purchased in the store.

Nozzles:

• for submersible devices;
• for hospitals (installed in a bowl).

According to functions they are classified into groups:

• stirring;
• for whipping;
• cutting (grinding products).

Special attachments are available (perform only a specific action) and universal ones.

Attachments for immersion blenders

Nozzles of various designs are attached to the “leg”:

• main chopper (in the form of blade knives);
• attachments with a perforated crown (for preparing fruit, vegetable and meat purees);
• hook – reinforced design for kneading dough with a dense consistency, suitable only for devices with high power;
• whisks in the form of a circle or frames for mixing;
• vacuum attachment (included with trays).

Conventional whisk attachments allow you to whip light dough, creams, and protein mixtures into a fluffy foam. Vacuum nozzles are installed in containers with products, then air is pumped out from there. As a result, the shelf life of food increases significantly.

Attachments for stationary blenders

In such units, nozzles are installed in a bowl. The kit usually includes several different types of shredders (basic set), but there are models with an expanded set of additional elements.

Nozzles available:

• graters;
• for preparing dough of various consistencies;
• knives for chopping food
• slicing discs;
• for cutting into cubes;
• juicer;
• for crushing ice;
• for creating emulsions.

The cutting elements are mounted on a rod inside the container and driven by the device’s motor. The lid covering the container has a hole for adding ingredients without stopping the blender.

Knives of blade designs are designed for grinding. Made from stainless steel, due to their strength, they grind and crush products of varying degrees of hardness. Knives and grating devices are installed in special disc holders. Used for slicing, producing vegetable or fruit shavings, and noodles. Since the cutting elements are arranged in fragments, sometimes defects “slip through” - large pieces.

Attachments for obtaining cubes consist of a special mesh, through the cells of which the product is pressed, and knives. When extruding, the cutting elements cut off the extruded part, producing a cube.

Using a paddle attachment, ice cubes and crushed ice are obtained, and a cone with vertical holes and ribs is convenient for preparing freshly squeezed juice from lemons, oranges or tangerines.

All types of blenders have dough attachments. Kinds:

• paddle attachment – ​​kneads light, low-viscosity dough;
• rotating hook - for thick dough.

The latest models of blenders include a spiral attachment designed to produce emulsions of uniform consistency. When using a whisk to mix two ingredients, air ingress makes it difficult to achieve uniformity. A vertically rotating spiral prevents such contact; the compounds are screwed into each other and distributed evenly.