Fishing rod stand: varieties and methods of making a fishing rod stand with your own hands for fishing from the shore and boats

A spinning stand is one of the most important and necessary equipment when fishing. It is that little thing you can’t do without while fishing.

Fishermen deal with this situation in different ways. Some people buy stands from stores, however, the prices for this product are too high, so every angler can try to design it themselves. If you don’t think about it in advance, coastal bushes and tree branches are used during fishing, but you can prepare a spinning rod holder before fishing and use it for a long time.

Single racks

A common type of homemade stand is racks, which can be one-piece, two-piece or combined. This stand can be easily installed on the ground of any bank.

There are racks that are screwed in, for example when there is hard ground on the coast, and which are driven into the ground. In the second case, it is important to use a rubber mallet so as not to damage the equipment and, of course, not to scare away the fish.

Rack-style stands ensure reliable holding of fishing rods, even in strong winds. Allows height adjustment and is compact for moving in a bag. The disadvantage of this type of stand is that it cannot be used on hard surfaces.

What are the advantages of fishing with feeder gear?

The advantages of this type of fishing lie in its compactness and mobility, because thanks to a small amount of equipment, the angler can move around the reservoir as needed in search of a promising place. At the same time, the use of feeder gear is justified both in currents and in still water, and in both cases it allows you to achieve very decent results.

Perhaps the main feature of the feeder is that the registration of bites when fishing with such a rod is carried out using a quiver tip, a flexible tip that sensitively reacts to the bite of even the smallest fish. That is, after casting the rig, the angler needs to remove the slack in the fishing line and tighten it so that the tip is in a slightly bent state. In anticipation of a bite, the rod is placed on a special stand, and I would like to talk about the manufacture of such a stand in this article.

Butt holders

This type of stand is different in that it holds the rod by the butt part, where the end of the handle is. Due to this design of the holders, the upper part is not stable enough, which becomes evident in unfavorable weather.

It should also be noted that this type of stand is fixed in the ground, so it cannot be used in any area (for example, concrete and rocky surfaces). However, with proper fastening, the main tackle holds securely, is compact and easy to use.

Mounting options

Both when choosing a holder in a store, and when making it yourself, first of all you need to decide on the type of fastening.

There are 4 standard methods:

• bolted - suitable for wooden and metal boats, this mount is very reliable, but the disadvantage is that it turns out to be stationary, so first you need to think carefully about where to place it;
• on screws - for wood, this method of fastening has the same advantages and disadvantages as the previous one;
• on glue - this is a good way to attach holders to PVC boats; if done correctly, this fastening is also very reliable, since rubber has excellent adhesion, but after fastening the structure cannot not only be moved, but even removed;
• on clamps - a universal method, suitable for any boat that has a suitable surface for fastening; on the one hand, the fastening method is reliable; on the other hand, the holder can always be easily moved to another part of the boat or simply removed.

There are also more original ways - installing an onboard mount for a fishing rod on a lyctros-likpaz and on oars, which will be discussed below.

Wooden pegs

Often when fishing, stands in the form of wooden pegs are used for feeder rods. Any fisherman is able to prepare them immediately at the fishing site. Spears are made from wood and then installed in the ground.

This option is applicable if a person is ready to destroy the ecosystem of a reservoir by cutting off bushes and trees near this place. Moreover, such a delivery can ruin the fishing rod, especially during hooking. When fishing is carried out on the open shore, a problem arises with finding the necessary vegetation.

What to do if there are no suitable materials

In some cases, if some materials are not available, a tripod is used instead of a stand, and ordinary pipe insulation is used instead of EVA. The cornice can be replaced with a metal profile of the appropriate size, and the finished stand can be painted using a regular can of paint. Not only feeder lovers prefer to have such combs, because it is convenient to put fishing rods on them for both carp fishermen and fans of float fishing.

Making a stand for a feeder with your own hands allows you not only to save a certain amount, but also to create the most convenient design for each specific situation, of which, as you know, there are many when fishing.

Pod genus

The most universal type of fishing rod stands is considered to be a kind of pod, the support for which can be a tripod and several vertical posts. If the support protrudes from a tripod that has only one hinge joint, then such a structure will not have high stability.

When using several rods, a rod with four posts is a convenient option. This stand can be adjusted, so it can be placed on any bank, choosing the required angle for tilting the fishing rod.

Note that if the stand is installed on a reservoir with standing water, then the rod will be located parallel to the shoreline, and if it is a river with a strong current, then the upper side of the feeder will be located much higher than the butt.

Blitz tips

• Rod holders not only simplify the fishing process, save physical effort when waiting for a long time for the next bite , but also extend the life of the spinning rod, since the prolonged presence of a fishing rod in the aquatic environment does not have a positive effect on its characteristics.
• Popular among fishermen, the pods are produced in two types - three-legged and four-legged. The three-support version of the product is not very stable, but does an excellent job of adjusting the tilt, allowing you to set angles in a variety of ranges. This characteristic minimizes the likelihood of tangling gear located nearby during fishing. Four-support structures are very stable, however, despite this advantage, they have a small tilt range and minimal adjustment speed.
• To avoid possible interference between the spinning rods located in the line when fishing for fish (reel snags and tangling of the fishing line are often observed), they should be placed in a checkerboard pattern.
• When choosing holders in a store, you should give preference to manufacturers that have been proven over the years. Carp Zoom, Salmo, EOS are considered the best on the market. The presented manufacturers produce devices exclusively from high quality materials that can last for many years.
• The stability of the holder is greatly influenced by the weight of the device. Large-sized products are more stable than less weighty models. However, it is worth remembering that the heavy design causes a lot of inconvenience during transportation, especially if the fisherman does not have a vehicle. Based on this feature, it is worth selecting products that maintain a balance between stability and weight.

Homemade spinning rod holder

Homemade holders come in two main types: for a single fishing rod and for several. The use of single holders is most convenient during feeder fishing. They can be made, for example, with stainless steel wire and aluminum.

In addition, the advantage of a single stand is that they are quite convenient when fishing is carried out in different places, and the gear and parts of different fishing rods will not hit each other.

The use of stands greatly facilitates the process of fishing, especially fishing with a feeder. Since, due to the stationary position of the rod and the strong tension of the line, even a weak bite is easily noticed. But for this it is necessary to ensure good fixation of the base, as well as stability in any weather.

Making a holder from a plastic pipe

Assembling a spinning stand from scrap materials

Holder for spinning rod in a boat

There are a number of requirements for spinning stands:

• a certain height of the stand, since the fishing rod must be positioned at an angle of 45-50 degrees from the surface of the water;
• the stand must have a U- or Y-shaped lock, which must have a smooth coating so as not to scratch the fishing rod.

Homemade wire stand

When making stands yourself, the most common material is metal wire, with an approximate diameter of 6 mm. A stand is prepared from it for attaching several spinning rods and a single fishing rod.

It is advisable to separate the points of contact of the stand (wire) with the fishing rod by wrapping them with electrical tape or some soft material, so as not to spoil its appearance.

A simple way to create a stand is also a design that has a pair of stops (length from 0.4 to 0.5 m) and a piece of wire with a diameter of 5-6 mm. The main material can be brass or steel so as not to damage the rod.

Stand made from a regular hanger

A convenient stand can be obtained from an ordinary plastic hanger. It is necessary to remove the hooks from the hanger and cut off all unnecessary parts. Then the lower part should be wrapped with thread and thoroughly coated with glue. This way we will get a securely fastened rod, and if necessary we will be able to change the tension level of the fishing line.

To make another version of the stand, strips (5 pieces) are purchased. Next, four elements are connected in the form of a square, and the fifth is used as a stop for the rod. The plank, which acts as a facade, has recesses that are half the thickness of the structure. Thus, this design will not be affected by any gusts of wind.

To ensure the stability of the stand, you need to secure the back surface with wire hooks.

Ski pole stand

The next type of stand for a large number of fishing rods is a coil. It can be made from 2 ski poles and a piece of wire. If we use a lot of fishing rods while fishing, it is easier to take two coils with us, on which up to ten rods can be placed.

In addition to these methods, you can prepare a stand using two plywood strips, the thickness of which is 5-6 mm, and several slats of wood with a thickness of 25 mm. Using a jigsaw, we cut 5 deep slots in the first plank to fix the fishing rods, which move freely in them. Next, we cut out many slots in the second plank in order to maintain a certain position of the rod.

Wooden stakes must be attached to the planks using screws so that they can be easily rotated. Moreover, the length of the stakes and planks should be the same. The parts of this stand need to be sanded and it is advisable to have a waterproof coating. The described design is convenient, has a compact size, so it easily folds into a bag or into a tube along with a fishing rod.

The big advantage of this stand is that instead of plywood, fishermen use available materials, such as PCB, plastic or aluminum. The choice of material for the racks is also free.

DIY tripod stand

Steel wire stands

Do it yourself

Most fishermen refuse to purchase store-bought stands, believing that it is better to make the product themselves, which will guarantee good quality and guarantee long-term use. In addition, such installations will not bring significant financial costs, which is a very tangible advantage.

Stand based on a metal rod

When making such a device, you cannot do without the following materials:

• directly without a metal rod with a diameter of no more than 9-10 mm;
• rubber;
• welding

Step-by-step work process:

• Using a welding machine , we make a semicircle from a rod, reminiscent of a stag.
• the resulting material with a soft rubber base.
• The next step is to weld the stand , which looks like a tube with a flat stand, to a metal rod.
• A stand for one spinning rod made according to these instructions can be used on any type of surface, which makes it especially attractive.

A stand for one spinning rod made according to these instructions can be used on any type of surface, which makes it especially attractive

Homemade genus under

If you wish, you can easily make a rod with your own hands, which is in great demand among fishermen. The manufacturing process requires:

• camera tripod;
• factory-produced stag;
• soft rubber or fabric.

Step by step guide:

• Having unscrewed the spear on the tripod, install the nut in its place.
• We fix the stag.
• A rubber or fabric base is glued on top of the stag, intended to function as a protective lining for the rod.

Stand made on the basis of a hanger

The job requires:

• plastic hanger intended for clothes;
• knife;
• glue "Moment";
• thread;
• two tubes.

Step by step guide:

• The first step is to remove the hook from the hanger , which allows you to hook onto the crossbar in the closet.
• Eliminate the presence of small parts located on the hanger.
• Using a thread, wind the entire surface of the device , which will make it possible to install at the desired angles and replace the tension.
• The bottom of the hanger is cut.
• The tube, on which 2 rubber rings are put on, acts as a lock.
• The homemade stand is ready for use.

The effectiveness of using homemade stands

The types of stands listed above are often used by fishermen, as they have a number of advantages:

• small weight and size;
• disassembling the structure into separate parts;
• ease and convenience of transportation;
• use when fishing for numerous species of fish;
• versatility in the form of fishing, especially in winter fishing.

Using a stand for spinning when fishing ensures the convenience of the process, gives freedom to the fisherman, since he does not need to hold the fishing rod in his hands for a long time, helps to extend the life of the rod, and also quickly notice the bite.

Equipment from well-known manufacturers

There is a fairly large range of products on the modern fishing equipment market. The most popular among spinning holders are the following models: Scotty, Kolibri, Avacha, Amphibalt.

Canadian Scotty stand

The manufacturer produces holders for spinning rods in a fairly large assortment.
Almost every product has a universal mount, with which this device can be fixed in any part of the boat: on the sides, transom, seats and handrails. The main advantages of holders from a Canadian manufacturer:

• using high quality materials as raw materials,
• Possibility of installation on any surface,
• adjusting the angle of the device up to 360 degrees.

All modifications of spinning stands are compatible with almost any adapters for installing Scotty holders on swimming craft.

Hummingbird model

Products under the Kolibri brand have been known on the market for a long time. The company offers high-quality stands for mounting on PVC boats. It has proven itself very well in the Russian and Ukrainian markets.

Product design:

• self-retaining device made of plywood has good moisture-resistant characteristics,
• slots for fishing rods,
• fasteners.

The plywood used for the production of fishing rod stands is pre-treated with a bakelite compound, which makes the material resistant to moisture. The fasteners are glued to the boat cylinders. Plywood is inserted into these fasteners. Using special clamping screws, the structure can be easily dismantled if necessary.

Avacha brand holders

Products from this company can also be installed on watercraft made of polyvinyl chloride.

Advantages of Avacha stands:

• a rather long glass does not allow the rod to fly out,
• the device is fixed on the side of the boat, so it does not interfere with the fisherman,
• the product has an attractive appearance, as it is made of nickel, which looks much more impressive than PVC pipes and aluminum.

Amphibalt devices

Rod stands of this brand are designed for mounting on a trolling arc using clamps with bolts. This connection is highly reliable. The product is made from 1.5 mm thick stainless steel sheet, so it is quite durable.

Types and features

Spinning holders come in various designs and designs. They are installed on boats made of:

• wood;
• metal;
• PVC.

The spinning rod holder is purchased or manufactured for specific installation conditions and in accordance with the size of the fishing rod. The following are classified according to the number of seats in the stand:

• single - compact device for one form;
• double – convenient to use for two spinning rods: for small and large – heavy wobblers;
• targas with a large number of glass holders. This type of stand is most often used in large water areas when traveling on a boat. Excellent for trolling: tackle with baits is thrown into the water, and the rods are securely attached to the glasses. With this placement, there is no overlap of gear, you can see which fishing rod worked.

The fishing rod holder is attached to the side or bench of the boat in various ways:

• using a clamp. One of the most used fasteners. It has a number of advantages over other installations: it is suitable for any type of boat, it simplifies installation - dismantling the holder, it is easy to control the screw tightening;
• gluing for PVC boats. Fits perfectly with quick release stands. You can glue several lower parts in different places on the side of the boat. During the fishing process, moving along the perimeter of the floating device, the upper part of the holder is rearranged by simply snapping it in;
• fastening with bolts or screws. Mainly used for permanent installation on wooden and metal boats. One of the most reliable connections, but requires periodic inspection and careful monitoring during operation. This connection is susceptible to corrosion, so lubricants should be used to protect against rust.

The clamp is used as a universal fastening for boats made of different materials.
The main place for installing such holders is the board for the bench. To avoid damaging the surface of the bench board, protective rubber pads should be used. For trolling, use holders with glasses that have a vertical position or an angle of inclination relative to the horizontal of no more than 600. The trolling method of fishing involves catching fish on a moving boat. Therefore, to securely hold the form, a high angle of its installation in the stand is designed.

For comfortable use, stands for float and feeder rods are made with the glass tilted at an angle of no more than 450, corresponding to the conditions for attaching fishing rods on the shore.

The design of the rod mount can be supplemented with a table with additional holes for installing containers with bait or glasses of tea or coffee.

A holder with an adjustable tilt of the holding part is suitable for the spinning rod, so that the spinner has the opportunity to independently set the installation position of the spinning rods that is convenient for himself.

Trolleys

How do you like it?

Beach carts are generally very common among our ocean-spoiled colleagues, for example, here’s a smaller option:

Another small fishing beach cart

Working example of axle assembly

Or this. As you can see, the person is engaged in this masturbation clearly not from a lack of funds.

An option for a small cart is a canoe stand.

Another boat option.

Very miniature and durable design.

This topic has become so widespread among kayakers that on the English-language Internet you can find detailed instructions with a list of parts for purchase and self-assembly. For example, here is https://palmettoka. build.html

Storage

The best place to store rod holders are special bags. It is convenient for fishermen to put these devices there along with alarms and backdrops without unscrewing them. The racks can be easily stored in bags even when not disassembled, where they will absolutely not spoil their design and appearance.

Each angler chooses a stand for carp rods according to his preferences. Of course, buying ready-to-use devices is much easier and saves time. However, making them yourself is much more interesting and entertaining.