How to change an old mink hat into a fashionable one: tips, ideas, diagrams with descriptions, before and after photos

Don't feel like shopping but want a new look? If there are outfits in your closet that you haven’t worn for a long time, then solving this issue will not be difficult at all. The question “How to change an old dress into a new one?” may be of interest not only to those who have things in their closets that have been gathering dust there for a long time. Many people have grandma's decorations that can also be repurposed. And someone might have a desire to combine two or even three outfits.

Upcycling old outfits is a great way to save money, show off your talent, and reduce your carbon footprint. But how can you transform an old dress into a new photo of which you can see below, so that you can safely “go out” in it?

Before altering an old mink hat, check the inside: tips

Important: Be sure to inspect the interior and the fur itself before starting work! The pile should not crumble, and the core should be dense and moderately hard, but not over-dried by time! If the product is already crumbling at the disassembly stage, then during sewing the core may even crack.

1. To remake an old mink hat, you need to completely or partially disassemble it. In any case, even if the changes are minor, we will definitely change the lining! To do this, carefully evaporate the old base and peel it off from the fur.
2. If you used a lot of gelatin when gluing, then wet the inside of the cap well. Don't get the fur wet! And lightly tear the flesh from the base.
3. When you have taken the hat apart, be sure to inspect the leather part! Old flesh can deteriorate, especially if it was poorly repaired. In this case, acid begins to accumulate, which literally eats away the flesh.
4. To do this, wet the flesh and pull it a little. It should become plastic and not tear.
5. If you are working with pieces, then trim off all the irregularities. You can just test them for strength - lower the fur trimmings into water for 10-15 minutes. Bad fur will literally begin to fall apart in your hands. You can't work with such fur! If the product is not sewn, then it will fall apart when worn.
6. Ideally, strengthen any punctured or worn areas. You can use special glue and thin fabric. Moment glue and spunbond (used in furniture production) proved to be the most durable We cut strips 1 cm wide, grease them with glue, and apply glue to the leather base.

Strengthen the fur around the perimeter and in weak spots!

What to make from a long skirt

Almost every woman has a long skirt in her wardrobe. It can gather dust in a closet for many reasons. From it you can sew:

• light dress;
• summer sundress with waves on the shoulders;
• beach attire;
• flyaway;

New life for an old thing

• short skirt;
• a circle or pencil skirt;
• blouse, jacket or vest.

From an old item you can sew many different things with your own hands that will significantly update your wardrobe and become a source of pride. What to sew from a long skirt is up to everyone to decide for themselves in each individual case. The product can be transformed from absolutely any material.

Transforming a product into a summer sundress

How to change a hard mink hat into a soft one?

We will start with this master class on how to alter a mink hat. After all, before, hats were hard and kept their shape well. Because we tried to gelatinize the base as best as possible. Today, not only has fashion changed, but such accessories have also turned out to be not very comfortable, since they often press. Therefore, we will begin our analysis with how to disassemble the hat and make it more convenient, without greatly modifying the appearance.

• First of all, we tear off the lining.

We work carefully so as not to damage the interior

• Now a little advice - if you see hand stitches inside, then this is a good sign. This means that the felt cap was dry when the skin was pulled on. This means that it will be easier to remove. If the felt had been wet, the bonding with the flesh would have been stronger.

Cutting the seam

Taking out the felt

• But in order for the headdress to keep its shape, it is worth leaving the upper part of the cap. To do this, we cut it out along the most protruding points.

Cut it out

• We insert it into our cap, secure it with pins in the center, and turn the product inside out. Now we sew the firth itself to the flesh and along the protrusion using normal hand stitches in a circle. Make sure that the stitches on the fur side are small and do not touch the pile itself.

Leave the top part hard to keep its shape.

• We outline the line of the future new hem. In this case, the fastening tape is light. Therefore, so that it is not visible and a new one is not sewn on, we simply change the hem line.

Celebrating

• To insulate and add some volume, we will insert batting. We take measurements on the hat for the desired size. Ours is asymmetrical, so we measure from all sides.

Measurements

• Cut out the batting to the desired size. To make the bottom of the cap a little thicker, insert a strip of drape - 4 cm to the circumference of your head. Sew directly to the fur part. On the pile side the stitches are small.

Sew on the drape

• We attach the batting. To do this, we lower it a little behind the strip of drape. We sew our batting to it.

Sew on

• Now we make a fur fold. For this we use thin felt. We cut it out in a semicircle and simply fold it into the widow and sew it to the desired place.

Making a fold

• Now we completely sew on the batting and secure it to the top of the felt cap. Sew the securing tape to the felt. You can optionally insert an elastic band or ribbon so that you can adjust the volume.

Closing

• We cut out the new lining on the bias. Never use old lining material! We also cut out a round base approximately 18 cm in diameter.

Cutting out the material

• We sew it, bend it at the top and also go through it with a stitch. Now we need to tighten the upper part. To do this, we pierce the fabric and now throw the material in a spiral. It’s like winding the fabric around a needle.

Then we pull the base together using the threads

• Distribute the folds evenly. We take an ordinary jar as a basis. First we place the round part, then the rectangular base. We secure everything with an elastic band or rope to prevent fidgeting. And sew it on by hand using a regular seam.

Sew on

• We insert our lining into the fur base and secure the bottom with pins. We place it evenly - the lining should be completely flush. We secure it with pins, and then sew it with a regular seam directly to the fur, capturing a millimeter of the mesh and about 0.5 cm of the lining.

Stitching

Eventually

Final stage

Now you need to sew a blank to the belt, since it is simply impossible to make a skirt out of a dress without an elastic band. To begin with, you should connect the individual parts of the product using pins. After this, you need to sew the edge of the skirt to the belt using a sewing machine, making a zigzag seam.

In this case, it is necessary to ensure that the entire edge is captured. Otherwise there is a risk of unraveling. Now you should remove all the pins. The skirt from the old dress is ready.

How to turn an old mink hat into a fashionable beret?

The beret is a symbol of femininity that can decorate almost any outfit. By the way, you might be interested in the article “Which hat to choose depending on the type and style of jacket or coat?” But back to our topic - it’s very easy to turn an old mink hat into a beret!

Restoration

In this example, two hats will be used, since the beret will be voluminous. Based on the pattern, you can roughly guess how much fur is needed. If you initially have a large hat, but want to make a small beret, then one headdress will be enough. Also, at your discretion, you can make the wedges narrower, but in larger quantities.

Pattern

Important: Takes a head volume of 56-57 cm. If you need a smaller volume, for example 52 cm, then take 9.5 cm at the widest part (indicated in green).

Cutting wedges

• We sew all the wedges together. In the example, the fur is from different hats, so the shade is slightly different. To beat this, we will alternate them with each other.

Sew along the entire length

As a result, we have two such semicircles

• We connect them in the center. Then we sew along the sides and form the base of the beret.

We fix it in the center

• Now we cut out the lower base of the beret. In our case, there is little fur, so the strip turned out thin. The bottom of a beret about 5 cm wide, folded in half, will look very nice. We sew all the pieces into one strip, focusing on the volume of the head + seam allowance + 2 cm for padding polyester, so that the headdress fits better and more comfortably on the head.

Cut out the rim

Important: Since it comes from wedges, the rim must be made from the same number of parts. At the same time, to add volume to the beret, we will gather the fur a little, sewing it to the bottom strip. This will also help you understand how much of our wedge you need to collect.

Part of the base is slightly narrower than the beret wedges

• We sew bias tape to the headband. Can be sewn on a simple sewing machine. But in this case, we place the trim at the bottom, and put newspaper on top of the core. If the flesh is hard enough, then the machine can handle it.

The flesh should be on top!

• Then we turn the binding inside out and literally sew a line half a millimeter from the edge.

Carefully sew the line

• Sew the fur rim to the beret. In this rim, between the bias tape and the base, we insert thin padding polyester, batting, or simply soft fleece-type fabric. To make the hat fit better, we sew on a thinner elastic band.

Rubber

• We sew behind the shirt at the bottom of the beret (at the junction with the headband) and behind the bias tape.

Sew on

• Now we cut out the lining; it’s better to use padding polyester. We also cut out 8 wedges + 1 cm along the edges for the seam + 3 cm down.

Cutting out the lining

• We sew it on a machine, turn it right side out, and take it back out. We put on a hat with a lining. We fasten with pins and sew well with hand stitches.

Stitching

Instructions

1. First you need to open the chest pocket. Then cut the dress into two parts along the waistline.

2. From the top you need to make a top, from the bottom - a skirt.

3. The bottom edge of the top needs to be turned to the wrong side twice, pinned and hemmed with a hidden seam on the arms. Then iron. If you have a sewing machine, you can stitch the hem on it.

DIY project: a fragrant and natural alternative to fabric softener

They don’t know what the other interlocutor wants: why the end of the conversation is postponed

Recipe for happiness: if life seems to be going wrong, ask yourself 10 questions

4. Now you need to make a drawstring for the elastic on the skirt. To do this, turn the top cut to the wrong side by 1 cm. Then apply an elastic band to determine the width of the drawstring. Fold the edge to the width of the drawstring, which should be slightly larger than the width of the elastic, pin or baste, then hem it by hand with a blind seam or stitch it by machine.

5. Take an elastic band and thread it through the drawstring using a pin or other available means - a pencil, a knitting needle or chopsticks. Make sure that the end of the elastic remains outside.

Pull the other end of the elastic out of the drawstring and sew or topstitch the ends.

The kit is ready. The top should be worn backwards, meaning the back of the dress will now be in front.

How to transform an old mink hat into a fashionable and modern headdress: complete restoration of earflaps

Now we offer you a master class on how to alter an old mink hat, which at first glance cannot be restored at all. But we assure you that the result will give you the opportunity to believe that nothing is impossible! Especially in the fur business.

Initial view

• Let's start cutting out the lining. At the same time, we do not rip, but rather cut off the fur, since the appearance at the seams can no longer be restored.

We cut off everything unnecessary without regret

Rip out all the seams

Cutting the insulation from the ears

• Now we need to check each skin! To do this, simply sprinkle it with water in some places.

Checking

• We wait 10-15 minutes. Gently stretch the flesh.

As you can see, the result is not always positive

• Now we need to refresh the color. To do this, take regular hair dye. Ideally, take chocolate and mix it with 1 part dark brown or half black.

Dye

• Carefully dye the pile and comb it with a pet comb in different directions.

We paint

• Rinse well until the water becomes clear. It doesn't hurt to use the balm that comes with the paint. We also rinse well. Dip with a towel to remove excess moisture.

Let's dry

• Now we will stretch the skins. To do this, we nail it onto a wooden surface with small nails or staples from a furniture stapler along the perimeter. If we talk about the right side - do as you feel comfortable. If you place the fur on top, you can brush it periodically, which will speed up drying.

Stretching What we have after painting

• We trim off any uneven edges or damaged fur.

Trimming

• We cut strips of approximately 0.8-1 cm. Please note that this must be done by weight. And for convenience, so as not to get confused in the stripes, do not literally cut 0.5-1 cm to the edge.

Making stripes Front and back views

• You can use another model at your discretion. We begin to wrap the front lines on the hat. Please note that we trim off bald patches or damaged fur. We don’t sew it yet, but we hide the ends inside, on the wrong side. We will sew them together at the end, not only with each other, but also sew them directly to the base of the hat.

We wrap around the entire perimeter.
A detailed master class on creating a hat from strips of fur is in our article “How to make a fur hat from stripes?”

• We will make the top of the head from another fur. We also cut it into strips. In this example, a silver fox will be used. If you have beautiful whole fur, you can simply sew on a piece of the desired size. You need to insert a hat elastic at the bottom. Just pull it through the knitted base, and not just through the fur.

Result

Are you one of those millions of women who struggle with excess weight?

Have all your attempts to lose weight been unsuccessful?
Have you already thought about radical measures? This is understandable, because a slim figure is an indicator of health and a reason for pride. In addition, this is at least human longevity. And the fact that a person who loses “extra pounds” looks younger is an axiom that does not require proof.

Therefore, we recommend reading the stories of our readers who managed to lose excess weight quickly, effectively and without expensive procedures.. Read the article >>

How to remake an old mink hat: ideas, before and after photos

We bring to your attention several ideas on how to remake an old mink hat.

From two hats

Beret

Knitting method

With ears

Option Idea

Different colors

Changing the style

We transform an ordinary T-shirt into a trendy Balenciaga top

You can make this top yourself at home. For this you will need:

• Long T-shirt;

Important! Please note that the T-shirt should have wide straps and be made of durable materials that will not fray during work.

• Scissors;
• Tailor's marker or soap;
• Sewing machine;
• Needle and thread in color.

Progress:

1. From the back of the T-shirt, cut the bottom so that the back is a few centimeters below the bra clasp.
2. Place the T-shirt right side out in front of you. Draw a vertical line in the middle.
3. Cut the product along the line to the very bottom.
4. Finish all edges using a sewing machine or overlocker.

That's all, the top is ready. Now you can put it on. To do this, simply wrap the long edges around your waist.