DIY snow scraper: drawings, video, photo

In winter, there is a need to clear snow from yards, walkways, driveways and other areas intended for the movement of people and vehicles.

Removing snow by hand is quite difficult, but you can make cleaning as easy as possible by building a convenient and practical cleaning tool.

How to make a snow scraper with your own hands, read the article.

Types of homemade snow scrapers

All scrapers have the same device. The equipment consists of a handle and a working blade, which is used to directly clean the snow. However, the shape and size of these elements can be different, depending on the purpose of the tool. For example, roof snow scrapers have a long handle. It can be solid or telescopic. The working blade is fixed perpendicular to the handle. The scraper is more like a rake.

To clear snow from paths and areas, scrapers are made wide. The simplest option is a rectangular sheet of tin or plywood with a handle. The stalk can be one or two, as well as straight or curved. A U-shaped handle is made on wide scrapers.

If we talk about assembling a scraper for snow removal with your own hands, then a scraper of this type sometimes has a working blade with side sides. The bucket allows you to capture a large volume of snow mass and transport it to a designated location.

Important! To make work easier when manually cleaning large areas, craftsmen came up with a type of scraper mounted on skis.

There are many configurations of snow removal equipment. However, all homemade snow scrapers have a main difference in the material they are made of. They create a tool from metal, plastic and wood:

1. Plastic equipment is most often purchased in stores. However, you can make such a scraper yourself from a used plastic barrel, tray or other household item. The plastic is lightweight and snow does not stick to it. Due to these advantages, the work with the scraper is simplified. The edge of the working blade is usually protected by a frame made of a metal strip, which protects the plastic from abrasion. Store-bought products have stiffening ribs. They give strength to the working surface. Plastic scrapers are lightweight, convenient, and do not stick to snow
2. The most popular tool for DIY assembly is a shovel-scraper for snow removal, where the material used is plywood and a wooden handle. It is not difficult to find a blank for such a tool in almost every home. Wood is easy to process, but has one drawback. Plywood strongly absorbs moisture. Over time, it begins to delaminate. A tool swollen with water becomes heavy, and wet snow sticks to the working surface. Wooden equipment is usually made from plywood
3. In terms of strength, metal scrapers come first. However, not all equipment is created equal. Metal is a flexible concept. If you use ordinary tin and a pipe for the handle, then such equipment will quickly rust. It's heavy. Snow is frozen to the working surface. Inventory made of galvanized sheet steel is considered optimal in terms of price and quality. The protective coating prevents the rapid development of corrosion. However, the scraper is still a bit heavy. Over time, the galvanized layer wears off and rusty spots appear. Aluminum scrapers are considered the best. The tool is lightweight, rarely freezes with snow, and does not rust. You can also consider stainless steel, but the metal is expensive. Metal scrapers are durable, resistant to moisture and mechanical stress

Despite many disadvantages, wood still remains one of the most popular materials.

Screw option

A device with a blade has drawbacks, and the main one is the waste of time and effort to remove the layer of snow picked up by the blade. Often it is left right next to the road, creating high snowdrifts, which is not always acceptable.

The version of the snow blower with an auger will allow you to get rid of even roadside sediment, because its design provides for the throwing of the captured mass over a distance of several meters. This will help clear the yard or street completely, leaving the piles next to the fence.

This option is welded or screwed from the front to a frame with wheels, which can be removed from an old wheelbarrow, for example.

Another design is a wheelless version, controlled by a tube. The body is mounted on a frame made of angles, from the bottom of which skis are screwed.

Main components and materials of both options:

• box - welded from sheets of metal;
• central shaft - is a ¾-2 inch pipe;
• gripper (scapula) - iron plates or pieces of channel;
• supporting elements;
• auger - made of rings or tape;
• motorcycle sprocket;
• ski made of plates or pipes;
• frame made of corners;
• bearings;
• a pipe for throwing out snow - you can take it from the stove.

Screw assembly sequence:

1. 4 rings and 6 support plates are cut from roofing sheets or other metal.

2. Six strips are placed on the shaft and welded to it at an angle of 90°. Then the sprocket is strengthened and the bearings are pressed in.
   Read also:  DIY fabric hearts: valentines for your soulmate!
3. Two blades made of plates are inserted between the middle guides. They are welded to the shaft and to the supporting elements. If pieces of channel bars are used as gripper blades, they are rotated 180° relative to each other.

4. The rings are cut, bent and welded so that two intersecting spirals are obtained.

You can straighten them in two ways:

1. Clamp the middle part in a vice, grab one edge with pliers and pull it to the side. Do the same with the other end.
2. Weld one edge to the support element at the blade and stretch it.

If the rings are made of thick material and it is difficult to grasp them with pliers, then you can use two clamping devices, such as a vice.

After making the auger, a sheet of metal is laid out and the box is welded. A hole is cut out in its middle part for a pipe to throw out snow. You can make it yourself or use one already prepared from an iron stove. Some craftsmen use plastic ones.

Then a rectangular hole is cut in the body opposite the sprocket to allow the chain to pass through. The box is installed on a frame with runners or wheels and the chainsaw is strengthened.

How to make a snow scraper with your own hands

Before you start making a scraper, you need to think about its configuration and size. See what material is available. First of all, the equipment should be convenient for work. The cutting is made according to the height of the person. If the working surface is wide, it is optimal to provide a U-shaped handle.

For a wide scraper, a double U-shaped handle is provided

It is optimal to choose metal from the materials for the working surface. However, such a tool can scratch paving slabs. If the yard has such a decorative covering, then it is better to choose plywood or OSB sheet. You can make an excellent plastic scraper for snow from a barrel with your own hands if you cut out a fragment of the side wall. It is important that the plastic is not fragile and at least 5 mm thick.

The material for the handle is a wooden handle or an aluminum tube. It is not advisable to use a regular steel pipe. Such a handle will be heavy, cold, and uncomfortable in the hands.

The tools you will need are a saw, a jigsaw, a grinder, a hammer, a screwdriver, and an electric drill. The exact list depends on what material will be used for the work.

Advice! If you plan to transport the scraper in a car, you need to consider a collapsible or folding handle.

Video of DIY snow scrapers:

Required tools and materials

Before choosing materials and making the device, you should remember that the chainsaw engine has little power. You should not use the unit to clear ice or heavily frozen snow to avoid damage.

First you need to think about what to make the cleaner from and what devices to use. It is not difficult to guess that different types of work will require different materials. They will be indicated in the instructions for the manufacture of a particular design.

What tools should you use:

• welding machine;
• hammer, pliers, screwdriver;
• different keys;
• file;
• grinder and drill;
• hacksaw;
• vice.

DIY snow scraper made of metal

If desired, you can make two versions of metal equipment: with and without sides on the working surface. The easiest option is the second one. For a working blade, a rectangular blank is cut out of sheet metal using a grinder. The height of the scraper is about 50 cm. The width depends on how many people the tool is designed for. If one operator will operate, the parameter is limited to 60-70 cm. For two people, the width of the working surface is increased to 1 m.

The handle is a wooden handle. It is installed alone on a narrow canvas. A wide scraper is equipped with two cuttings, and at the end they are connected by a jumper. The handle is shaped like the letter “P”.

The presence of sides allows you to capture more snow

Using the scraper principle, you can construct a homemade snow scraper with your own hands if you equip it with sides. Here too there are two options. In the first case, the rear and two side sides are bent from metal. If you make them high, the bucket will be convenient not only to scrape off, but also to remove snow from the site.

In the second option, the metal ones bend only the side sides. The back shelf is made from boards. It additionally serves as a solid basis for fixing the cutting.

Application of manual snow blower Forte QI-JY-50

This is a simple snow blower model that is suitable for clearing small areas. The equipment is suitable for a summer house, a small yard, to make a path to the porch or garage doors. Easily cleans hard-to-reach and narrow areas of the yard.

Convenient to use

Snow blowers Forte QI-JY-50, Huskvarna, cmi 163, snow fox sf16353l, lux 163, Champion 656, Patriot, Champion are effective against freshly fallen loose snow. Easily removes sediment up to a layer of 7 cm; with a larger layer of sediment, you will have to make some efforts to clear the road.

The model is supplied unassembled. Assembly does not require special knowledge or skills - even a schoolchild can cope with the task. It is convenient to store the QI-JY-50 model in any utility room - it takes up a little more space than a regular shovel.

How to make a snow scraper for skis with your own hands

The disadvantage of all inventory is the complexity of management. While pushing, the scraper collects snow well only on a flat surface, but no matter how smooth it is, the working surface still hits pieces of ice, ground and other obstacles. Each blow is reflected by the load on the back. A cleaning device installed on the skis helps solve the problem.

The working blade mounted on skis does not rest against the ground when raking snow.

To make your own snow scraper, use a grinder to cut off two corners, pipes or tires 1 m long. The ends are bent, otherwise the skids will hit the ground while moving. A U-shaped handle is bent from a tube with a diameter of 15 mm. It is welded to the runners at an angle. Bend towards yourself. The angle is determined individually so that it is convenient to control. A rectangular metal sheet is bolted to the posts of the U-shaped handle. The lower edge of the working blade should be on skis so that it does not rest on the ground.

Model selection

Manual wheeled bulldozers are produced by many manufacturers. The principle of constructing snow cleaning equipment is the same. Dimensions, design and some minor design nuances differ.

Snow shovel on wheels Elektromash

A popular domestic development is a manual two-wheeled bulldozer. Equipment allowing for cleaning work has the following characteristics:

1. The blade is made of 2 mm steel. Working width 70 cm.
2. Movement occurs due to 2 wheels. The rubber run does not damage the decorative surface of paving slabs.
3. The blade is equipped with a mechanism that allows you to adjust the angle of rotation.
4. The tool is easy to operate thanks to the adjustable handle. The length is set according to the height of the operator.
5. A special stop prevents the lower edge of the knife from cutting into the ground during harvesting work.

The weight of the tool is about 11 kg. Light weight and high maneuverability allow an elderly person to operate the blade.

Wheeled snow shovel Bulldozer

The two-wheeled blade of the “Bulldozer” series is distinguished by increased bucket dimensions. In one pass, the working width of the strip is 80 cm. Plastic wheels do not damage paving slabs. The Bulldozer model has the following characteristics:

1. The steel blade easily cuts off ice build-ups and compacted snow layers. Durable metal does not deform from impacts against hard objects during cleaning.
2. The adjustment mechanism of the blade allows you to change its angle to move snow accumulations to the edge of the curb.
3. The handle is equipped with two adjustment mechanisms. The operator is given the opportunity to change the angle of inclination and length.

Even an elderly person can clear snow drifts with a two-wheeled bulldozer, applying a minimum of physical activity.

Shustrik-3 device

The two-wheeled device “Shustrik-3” is characterized by increased maneuverability. The tool is easy to move over obstacles; you can simply carry it by hand or roll it on one wheel, lifting one side. Even a child can use the scraper. The handle is equipped with an adjustment mechanism that allows you to change its length. The blade is convenient to maneuver on narrow sidewalks, enter hard-to-reach areas, and go around obstacles when cleaning areas with flower beds, pillars, and sculptures.

The steel ladle is 60 cm wide and 20 cm high. The width of the adjustable handle is 41 cm. The tool is equipped with a rotating mechanism. When removing snow accumulations, the bucket is directed to the right or left. If you just need to push the snow out of place, the blade has a turn to the other side.

The video demonstrates the removal of snow mass by a nimble:

Shovel Snowball

The four-wheeled shovel “Snowball” will replace a full-fledged bulldozer and will help clear snow over a large area with minimal effort. The inventory is managed by one person. However, 4 wheels, a powerful frame, a wide bucket and a handle allow you to use the tool with greater productivity. If you put 2 people in control, you can use a shovel to move large accumulations of snow, knock down ice build-ups, and clean compacted wet layers.

The adjustment mechanism allows you to set the desired angle of rotation of the bucket. Rubber wheels do not damage the sidewalk surface and move the cart smoothly over uneven surfaces. Control occurs at full height or at an angle, which is chosen by the operator himself.

Video about using the four-wheeled snowball tool when clearing snow:

How to make a snow scraper from plywood

For snow removal equipment you will need a plywood sheet 6 mm thick. The workpiece is sawed off to a length of 0.8-1 m and a width of 50 cm. The plywood is bolted to a U-shaped handle curved from a metal pipe or assembled from wooden cuttings. The scraper is almost ready, but it’s too early to clean the snow with it. In this form, the ends of the working cloth quickly wear out. The plywood begins to delaminate and break off in splinters.

It is optimal to frame the plywood with a steel strip

To improve the design, the lower end of the working blade is framed with a steel strip. It is fastened with rivets through through drilled holes.

Advice! A good handle for a scraper can be made from the frame of an old clamshell. The aluminum tube is durable, lightweight, and comfortable to hold with your hands.

Do-it-yourself scraper for removing snow from the roof

Snow covers not only paths, but also roofs. On the one hand, he doesn’t interfere there. However, it needs to be removed. Large accumulations of snow can cause the roof to collapse, and when an avalanche falls from the roof, there is a risk of injury to a person. A regular scraper won't do the job here. A long-handled device will be required. There are many options, but one of the simplest designs is considered to be a rake scraper.

They begin to assemble a homemade scraper with their own hands for removing snow from sawing off boards. The workpiece is taken up to 800 mm long and up to 200 mm wide. In any case, the board must cover the rake teeth, otherwise they will damage the roofing.

The board is fixed to the rake with a steel tire and self-tapping screws

The board is laid on the ground. A rake is placed perpendicularly on top. In this position, the teeth are parallel to the plane of the board. Now the elements need to be securely fastened. To do this, take a tire. Its length should exceed the width of the rake. Holes are drilled in the tire, placed on the teeth, and screwed to the board with self-tapping screws.

Snow is cleared from the roof by moving it towards you with a rake.

The only drawback of the design is the short handle of the rake. It is extended with an aluminum tube or a long wooden strip is used.

How to provide driving force for a snow blower?

He will need a gasoline or electric engine or walk-behind tractor. It is believed that a snow blower for a walk-behind tractor is best suited, since in this option everything is already ready. All that remains is to install and connect, and you can operate the device. For it, you can use three versions of attachments for clearing snow:

• Along with rigid, rotating rings. They will help cope with snow that has fallen recently and has not yet frozen.
• Based on a suspended version of the blade equipped with knives. Suitable for dealing with snow that has lain for some time and formed a dense form.
• But a rotary snow blower is considered the most reliable option. It helps to throw snow a long distance from the place where it is necessary to create sufficient space for passage.

How to make a snow scraper from 0SB

When you urgently need to remove snow, and you only have a piece of OSB board at hand, you can make a scraper using simple manipulations with a jigsaw. To assemble a scraper with your own hands for clearing snow, you don’t need drawings, but you need to build a pattern.

On the OSB board, draw the shape of the future scraper with a pencil. Towards the bottom, the drag scraper is expanded to 1 m. The corners are slightly rounded. Toward the top, the plate is narrowed approximately 30 cm from each edge. Two oblong holes for handles are drawn on the pattern. Now all that remains is to cut off the excess parts of the OSB board using a jigsaw according to the markings. The area near the handles is carefully sanded with sandpaper. For convenience, they can be wrapped with electrical tape.

Principle of operation

The power unit starts up and rotates the auger, which, in most cases, has a spiral shape. In rotary snow blowers, the guide elements are straight.

Thanks to him, the snow is raked and thrown to the side. Moreover, this operating principle is relevant for all models, regardless of cost. As the price increases, headlights, heated grips and other extras are added.

DIY snow scraper with brush

The store-bought version of a scraper with a brush resembles a double-sided rake, only instead of teeth there are bristles on one side, and a rigid base is fixed on the other side. When cleaning, first scrape off the bulk of the snow, and then sweep away the remains with a brush.

A shop scraper with a brush is usually equipped with an aluminum telescopic handle, which allows you to remove snow from a height, such as a roof.

In the DIY version, you assemble a snow scraper with your own hands from plywood, securing a long handle perpendicular to the rectangular blank. One side is framed with a tin strip. Bristles from a plastic broom or brush are applied to the other side of the workpiece, pressed with a metal tire and secured with self-tapping screws through the drilled holes.

Where is this technique used?

A universal snow blower is designed to clear large areas of snow. The basic principle of throwing the snow cover to the side is similar to human labor, only more economical. There are no complex components in their design, which increases operability and maintainability.

Roads and road transport structures of any complexity. Special design workshop “Spetsroad”: TDR – traffic management project. Design since 2010, significant experience in passing and approving state and commercial examinations.

In addition, anyone can handle their operation. With a large area, it is simply impossible to do without such a device.