Free tube from a PET bottle: how to make it and what to make from it

Preparation of material

Before you begin the work process, you need to prepare tools that may be useful in making tubes from plastic eggplants. The list of necessities includes:

• wooden block;
• an electric drill with a set of drills, you will need the thinnest ones for the job;
• PET bottles;
• ruler;
• self-tapping screws for fastening the bar;
• pencil;
• construction hairdryer

Plastic bottles are selected taking into account the color that you want to give to the future product. The containers must be clean and dry, so if necessary, they are first cleaned and dried in the sun naturally.

Tools

To carry out step-by-step assembly of a drain from a polymer container, you need to prepare the appropriate tools. Let's look at what devices are used for this type of work:

• scissors or sharp knife;
• furniture stapler;
• screwdriver

Scissors are needed to cut out the main elements from the middle part of the plastic container. Instead of a furniture stapler, you can use a large office device, the width of the staples should be from 10 to 12 mm. A screwdriver is used to fix the brackets.

Note! The bottoms of containers remaining after cutting them should not be thrown away. They can be useful as plugs for a homemade drainage system.

Step-by-step tube manufacturing

Making tubes from plastic bottles is not difficult, as the material is easy and convenient to work with. There are several manufacturing methods. In the first case, you should proceed according to step-by-step instructions:

• carefully cut the eggplant in the form of a long ribbon, its width should vary between 0.6-0.7 cm;
• using a prepared drill, drill a hole in a wooden block, its diameter should be 0.28 cm;
• securely fix the block to the work surface using self-tapping screws; it should not dangle during the process;
• insert the polyethylene tape into the hole, push it slightly, and then direct a hot stream at it with a hair dryer;
• slowly pull the plastic tape forward, so you can see the tube at the exit.

If you don’t have a hair dryer available, you can use boiling water. That is, the tape is dipped into boiling water and then pulled through the hole using a clamp, then you don’t have to worry about burns from the steam. When the finished tube cools, the required rigidity and strength appear.

In these simple ways you can quickly, and most importantly, without any effort, additional financial investments or complex equipment, produce the material needed for household needs.

We recommend: Have you submitted data on water meters via the Internet? Now you can do this at Gosuslugi

It can be applied anywhere. In addition, in this case, you can usefully get rid of plastic bottles that have been accumulating for years.

Wire fence

When there is a need to enclose flowers in a flower bed with a higher structure, it makes sense to build a decorative fence from bottles strung on wire.

Step-by-step installation instructions

Work should begin with a preliminary calculation of consumables

It is extremely important to immediately determine the size of the fence, because you can build a fence of any height

In order for the structure to have an aesthetic, neat appearance, it is made from identical spans with an equal number of fragments.

• To avoid distortions, use a ruler and marker to mark the areas of punctures for the wire on each fragment.
• Make holes in the bottles with hot wire or a soldering iron.
• Mark the area and install support posts.
• String the bottles onto the wire and connect them into sections.
• Secure the sections to support posts.

Use of finished material

Plastic bottle tubes can be used in many different ways. There are several ideas for using homemade material:

1. You can make a chain-link mesh that will protect your garden plot from animals. Advantages of a homemade product: strength, ease of manufacture, the material is not afraid of the lowest and highest temperature conditions, so the tubes can be used in both severe frosts and heat. They are simply intertwined to the desired width, height and length.

2. An excellent idea for using pipes is to create a drip irrigation system for a garden plot. Such a device will not rot from constant contact with water or wet soil. And less effort and time will be spent on watering activities, since the system will do everything on its own without the participation of the gardener.
3. Some craftsmen use plastic tubes to create original designer lamps. They can have any shape, color and size. In addition, plastic perfectly transmits and diffuses light. You can create a great shade for a table lamp or update an old and faded floor lamp.
4. Tubes make excellent jewelry: bracelets, keychains, photo frames. They are easy to make with your own hands; the resulting products look original and stylish. There are many ways to weave beautiful patterns; accessories look fashionable, simple and creative at the same time.
5. Experienced craftswomen weave durable baskets, drawers and boxes from tubes for storing all sorts of small items. Such things look very interesting and can become an excellent decoration in the interior.

6. A vase made from plastic tubes looks beautiful. In addition, anyone can create such a fake; no experience is required. You can beautifully braid flower pots with tubes.
7. Lovers of weaving with beads make material for working with their own hands. They simply cut the tubes to the required size and use them to create original gizmos. Homemade beads allow you to save a lot, since you no longer need to purchase ready-made beads.

We recommend: How to choose and sew a ribbon to a curtain?

There are a lot of ideas for using plastic tubes, just use your imagination and you can create a unique thing that you won’t see anywhere else.

A handmade craft will be an excellent present for relatives, friends or colleagues. In addition, to create straws you do not need to purchase material; empty plastic bottles can be found in every home.

The best manufacturers

ARNETOLI MOTOR

The Italian manufacturer has been manufacturing trimmers and equipment for them for more than 20 years. The choice is very wide; the consumer can choose the model for himself based on power, diameter and cross-section of the fishing line.

Advantages:

• Introduction of new technologies.
• High quality equipment.
• A wide range of.
• Affordable price.
• The line is wear-resistant, durable and lightweight.
• Low noise level during operation.

Flaws:

High price.

OREGON

The American manufacturer is the world's leading developer of trimmer lines. To make it easier to differentiate between types of products, they are painted in different colors. This is one of the main advantages of the large number of products produced.

Advantages:

• Reels are available both in small winding and in coils.
• High quality wire.
• Using different models.
• Particularly durable series are designed for any vegetation, even thorny bushes.
• Series of different profiles, diameters and compositions differ in color.

Flaws:

• Considerable cost.
• With a long storage period, the fragility of the fishing line increases.

CHAMPION

The Chinese company, despite its youth, has already conquered the market thanks to the optimal price-quality ratio. Raw materials for products are supplied from other countries: India, USA, France. The company produces both the equipment itself and branded cords for it.

Advantages:

• Affordable price.
• The quality of the fishing line is rated by consumers as the best among budget models.
• Reels are available in different winding lengths.
• The models are equipped with a special knife for cutting.
• For convenience, the fishing line is available in a variety of colors.
• The wear-resistant core consists of two layers of material and has a twisted structure.

Flaws:

• It makes a loud noise when working.
• When the device heats up too much, the ends of the fishing line begin to melt.

HUSQVARNA

The famous Swedish company has been producing garden equipment for more than 400 years. It has won global success thanks to the high quality of its products. The line is produced both complete with trimmers and separately from them.

Advantages:

• Large assortment of goods.
• Reels and coils of various windings.
• High wear resistance.
• The line is compatible with any trimmer heads.
• The special shape prevents breaking, fraying of ends and their melting when heated.
• Many options for silent fishing line.

Flaws:

High price.

STURM

The young German trading concern has been supplying its products to the Russian market for only 15 years. The production itself is located in China, which reduces the cost of production. The fishing line is available in reels, coils and coils, and has different colors for ease of selection.

Advantages:

• Affordable cost of fishing line.
• Various winding lengths.
• There are especially strong cords with a steel core.
• The company has a system for checking product quality.

Flaws:

• There is no division of products into series.
• The fishing line can be sold without packaging.

REZER

The ranking of the best also includes a domestic manufacturer of fishing line for trimmers. The company produces three main series of cords: with a cross-section in the form of a star, an ellipse and a square. There is also a particularly strong heptagonal fishing line. The reels have a winding from 15 to 114 m.

Advantages:

• Low cost.
• High quality grass cutting.
• To protect against heat, the fishing line is coated with heat-resistant material.
• Possibility of choice by color.
• Low noise level during operation.

Flaws:

• It wears out and breaks quickly.
• Not intended for rocky areas.

ECHO

Speaking about manufacturers of garden equipment, one cannot help but recall the Japanese company ECHO. It produces light agricultural equipment and fishing line for it. The company offers several lines of its products. It differs in color, different cross-sectional shape and thickness.

Advantages:

• Mows any plants.
• According to manufacturers' reviews, it is of excellent quality.
• Universal application.
• The cord is resistant to breaks and abrasions.
• Available in convenient form in coils and coils starting from 10 m.

Flaws:

• Products are not often found on free sale, as they are quickly sold out.
• A fishing line with a thick section unwinds more slowly.
• It has a high cost.

Section types

There are a lot of types of fishing line, you don’t have to pay attention to the color - there are no general “color-characteristic” standards as such. The type of string section becomes an important factor; it is chosen depending on the type of grass.

1. The circle is a universal fishing line. Smooth lines have a higher noise level when mowing; twisted lines, on the contrary, mow more quietly, but are consumed faster (like any type of twisted line).
2. Square or polygon. This fishing line is more effective than round fishing line - sharp angles cut stems faster and better.
3. Star, ribbed or twisted square. Has maximum cutting efficiency and speed.

It is important to know! It is strictly forbidden to use metal wire, cables or rods instead of fishing line. Such equipment easily cuts even leather shoes and can seriously injure the operator.

Which bottle should I take?

The experience of practitioners has shown that the best results are obtained with smooth bottles . The transverse strips make it difficult to cut the line, but are usable. But longitudinal reliefs slow down the rotation, the tape breaks and breaks.

There is no clear answer regarding the color of the source material. Some fishermen consider colorless plastic to be optimal, while others successfully fish with colored fishing line. Its advantage is that donks are clearly visible from afar, and there is no risk of losing them. For commercial use, color is not particularly important.

With careful work, you can cut more than 30 meters of millimeter fishing line from a 2-liter bottle.

Basic parameters of trimmer line

Fishing lines can be classified according to the following parameters:

• Thread thickness;
• Section shape;
• Composition of the fishing line.

Thread thickness

You can find out about it by reading the trimmer’s performance characteristics or by looking at the dimensions and inscriptions on the universal bobbin. Typically, trimmers use threads with a diameter of 1.2-4 mm. True, for each device you will have to select a fishing line of a certain diameter.

A thread for a trimmer that is thinner than required will not immediately damage the engine, although it will significantly increase its wear. If you use thicker filament than necessary, the rotational resistance will increase, the motor will work harder, overheat and, as a result, break down. True, a lot depends on the engine itself.

You can also find out the approximate diameter of the fishing line for the device by the type of engine. If the trimmer is powered by electricity or battery and its power is 1 kW, you will need a cutting thread with a diameter of 2 mm, and if its power is less than 500 W, use a fishing line no larger than 1.6 mm.

For a gasoline trimmer, the fishing line is chosen with a certain diameter - 2.4 - 3 mm. The choice of such a thick fishing line is related to the characteristics of gasoline units - they are more powerful and more productive than their electric counterparts. Thick fishing line can be used for a long time; in addition, it can easily overcome long-term dead wood.

Section shape

The most commonly chosen line for electric scythes is the one with a round cross-section. It is inexpensive and the most popular, it mows fresh grass well. Its main drawback is the noise level emitted, which can be heard while the trimmer is operating. The noise of the fishing line is close in intensity to the hum of the engine. For the best noise reduction, manufacturers suggest using a spiral-shaped fishing line.

Today they also produce square-section line for trimmers. Other shapes are quite common: rectangular and star-shaped. Fishing lines that have jagged edges and sharp edges are especially productive. Such edges cut the grass more evenly.

There are also options for fishing line with notches and dents. They can be used to mow large weeds. The noise level emitted by such a fishing line is low, and due to the increased aerodynamic properties, the trimmer is given additional power. Such a cutting element is installed on powerful trimmers that are planned to be used to carry out work in overgrown, neglected areas.

To work with this type of fishing line, special heads are installed on the brush cutter. The fishing line is wound around them. It copes with all types of grass (especially weeds) and shrubs. But its cost is quite high. The consumption of such fishing line is also high, since when it is fed from the reel, it may be difficult to remove it. It is usually used with discs into which it is inserted in small sections.

There is also a two-component twisted trimmer line. Its purpose is high-quality mowing of dead wood. It is distinguished by its round cross-section, tear resistance and increased strength. It comes with a core made from a different material. Twisted line is only suitable for gasoline trimmers. It can cope even with small bushes. Its main disadvantage is its high cost. For daily work, purchasing twisted fishing line is quite expensive.

Line composition

It is the composition that determines the service life of the fishing line. It is often made from nylon. It wears slowly and improves performance at high temperatures and heavy loads. The material retains its working properties for a long time; low temperatures do not affect it, nor does long-term operation.

Coaxial line for trimmers is considered one of the strongest. It has a dense core, and therefore wears out gradually. This line is difficult to cut with a knife and creates little noise during operation. Also now there is a fishing line that contains inclusions of aluminum.

Shape and size

Networks come in various forms:

• Single-walled. The simplest form and has upper and lower selections. These selections are attached to the cores, which are located on both sides of the network. The height of the veins is 20 percent less than the network.
• Two- or three-walled. Complex shaped networks called tangles. This is due to the fact that the fish get entangled in it.

The length of the networks can also vary and can range from 20 meters or more. The height of the nets (for industrial fishing) ranges from 1.5-1.8 meters. Accordingly, the nets also have different cell sizes depending on the size and size of the fish:

• 20mm – for live bait and small fishing;
• 27-32mm – for roach and perch;
• 40-50mm – for bream and crucian carp;
• 120-140mm – for trophy pike.

About the options

If you try, you can do it without a hairdryer and a screwdriver. The rotation is accomplished with a stick, and the source of heat can be a lighter or a torch. True, it is better to use reliable tools. You can make the fishing line in several layers. It will be strong and elastic. This is useful to use in trimmers. Industrial fishing lines are expensive, but with your own hands, using the described scheme, you can make a product in unlimited quantities for mere pennies. In addition, you can make a product of any thickness, even one that is rarely found in stores. The fishing line made in the described way is strong and can cope with greater loads than industrial ones.

How to make a moped with a motor from a brush cutter?

Assembling a homemade trimmer begins with studying detailed drawings. The diagrams must indicate the dimensions of the parts used, as well as the sequence and methods of their installation into the overall structure of the moped.

Next you will need to prepare the equipment and parts.

Their list includes:

• drive motor;
• gearbox;
• brake system;
• welding machine;
• Bulgarian;
• set of bolted connections;
• set of wrenches and screwdrivers.

The further procedure for assembling a homemade moped from a trimmer should be divided into several stages. Each of them must be treated with special responsibility, since not only the quality of the device depends on it, but also the safety of the operator during its operation.

Trimmer reel modifications

Reels (heads) for trimmers can be of various modifications. Thread the line into the trimmer. Using the makita um 4030 trimmer as an example. How to thread fishing line into the trimmer. Single-string lines (with one strand of fishing line) are suitable for trimming the lawn, and for clearing areas and mowing grass. two-string, with manual adjustment of string length or automatic line feed.

Modern manufacturers are increasingly producing universal brush cutters with two-string automatic reels.

• Line and reel for trimmer: how to make the right choice
• How to make a bite alarm
• How to catch pike with a wobbler in 2022

We increase the efficiency of the trimmer: replace the fishing line with a chainsaw chain

As the owner of a gasoline trimmer, I noticed the fact that the fishing line, even the thickest, cannot cope with young growth (especially there is a lot of it around tree trunks). You can use knives, but they are not suitable for thin grass (and wearing them specifically to cut several thick branches is downright lazy), so I found a great alternative solution

What you need to have on hand We will need the following tool:

• Welding machine;
• Drill, set of metal drills;
• Vise;
• Marker and ruler.

From materials:

• Large concave cup used to secure trimmer blades, flat washer and nut;
• Old chain from a chainsaw.

Preparatory work: processing the locking washer Using a ruler, mark a straight line along the diameter on the concave washer and clamp it in a vice with one of the markings facing upwards.

It is better to first mark the drilling location with a core so that the drill does not slip. We make holes on both sides, first with a thin one, and then with a larger drill - the diameter should be such that the chain can easily pass through.

Installation and fastening of the chain We pass the chain through the holes, laying it along the inner wall of the washer so that it cannot interfere with the drive axis of the trimmer.

At this stage, it is important to accurately measure the length of the chain from the ends to the washer. It must be the same and not exceed the permissible dimensions, otherwise the protective casing will be immediately destroyed

From the inside, we securely weld the chain to the washer.

All is ready. We put a flat washer on the trimmer axis, our modernized washer and tighten it with a fixing nut.

When performing the work described above, you should not only follow the rules for using power tools, but also not neglect personal protective equipment.

Tests

The chain is not a fishing line - its effectiveness exceeded all expectations! It copes well not only with growth around trees, but also with impassable thickets, including reeds and even thick corn stalks.

Results As it turned out, the modification is essentially very simple, and if you had everything you needed, it took 10-15 minutes, no more. You just need to have an idea of ​​how to use a drill and a welding machine.

Using a chainsaw chain not only greatly increased the efficiency of the tool, but also reduced maintenance costs - in any case, I no longer need string for the trimmer.

Safety first!

Don't forget about safety precautions when working with a trimmer! Fragments of bushes are scattered over a long distance and with great force. Use personal protective equipment - a special mask, make sure that there are no people or animals around. Watch the video Source

You may like:

• Crocheted rugs: interesting patterns, patterns and…
• Crocheted rugs: interesting patterns, patterns and…
• DIY quality kitchen knives
• Beautiful and original New Year's crafts 2018
• Unusual use of PVC pipes. Ideas
• Highly efficient DIY solar collector
• Edible bouquets: varieties, rules...
• Budget Belt Sanding Machine
• Mesmerizing and strikingly beautiful wings...
• Solid board table and bench
• Any sewing machine is sold with a certain...
• My linoleum looks like new... HOW TO WASH...