How to make a “FLOATING” bed: 480 drawings and step-by-step photos

DIY floating bed

Do you want to make changes to your bedroom interior? How do you like the idea of ​​making a floating bed with your own hands ? It's not too difficult, even if it's a big project. A floating bed can be a fresh addition to your bedroom design as it presents a minimalist modern aesthetic while adding a feeling of spaciousness to the room. Our article presents several wonderful examples of how to make a bed with a floating effect , which will allow you to acquire original furniture even on a limited budget. Here there are projects of a floating bed with lighting , on wheels, with a beautiful solid wood headboard, and even an example of a floating bedside table. You can use links to primary sources, read instructions on how to make a floating bed with your own hands with drawings and detailed master classes with step-by-step photos.

The main advantages of floating beds

A floating bed will fit perfectly into any modern interior. With its minimalist design it will create a unique atmosphere of lightness and purity. In addition to the unusual appearance, such furniture has a lot of other advantages, namely:

Articles on the topic (click to view)

• Differences between an ottoman and a bed
• Anatomical bed frame
• Differences between a sofa and a sofa
• How to choose the right foam density for a mattress
• Canape furniture: what is it
• How to beautifully hang a picture on the wall
• The best cleaner for leather furniture

• variety of shapes – designers offer a large selection of shapes and sizes of flying beds. There are products of both traditional rectangular or square design, as well as flying beds of round and other non-standard shapes;
• comfort - usually such furniture has a fairly spacious sleeping area, designed for one or two people, as well as a large selection of models;
• thanks to the presence of illumination from below, additional lighting of the room is provided;
• Despite, at first glance, the lightness of this design, it is quite stable and reliable. In addition to the central supports, from which the rays extend in different directions and due to which the load is evenly distributed over the entire surface, some models provide for fastening the bed with the back or both sides at once to the wall. There are also floating beds with regular legs, but made of tempered glass, which makes them almost invisible;
  Read also:  Do-it-yourself wind generator from a motor-wheel: proven assembly recommendations
• versatility - this bed can be used as a sleeping place for both a married couple and an adult, child, teenager and other family members;
• convenience and practicality - the absence of legs does not limit movements during cleaning and does not clutter up the bedroom space, creating a feeling of freedom and lightness.

Attention! when choosing such a bed for your bedroom, it is important to remember that it does not provide storage space, as in conventional models; you cannot put anything under it, since the appearance of the product and its main advantage will be lost.

What is

A sleeping bed suspended in the air, despite the apparent weightlessness, is a strong, reliable, stable product. The flight effect is created due to the absence of the usual legs. A single leg is used as a support, which is invisible under the bed. The LED lighting located under the sleeping bed gives the product a beautiful look. Furniture with a unique design has its own pros, cons, and features. Modern models are characterized by the following advantages:

1. Original stylish design. After installing the product in the bedroom, its interior will become unusual.
2. Comfort. As a rule, such beds are made with a large sleeping area.
3. Fastening strength. The product is simultaneously attached to the wall and floor, so it does not wobble.
4. Availability of space under the bed. A mop can easily clean hard-to-reach areas.

If desired, you can make an original piece of furniture with your own hands from inexpensive materials according to individual sizes. However, the unusual sleeping bed has some disadvantages:

• complex manufacturing, requiring certain skills in working with wood, plywood, metal;
• lack of drawers under the bed for storing things;
• difficulties when moving furniture to another place.

But these shortcomings are fully compensated by the beauty and originality of the item for sleep and relaxation.

Material of manufacture

The floating beds that manufacturers offer today are quite diverse in their design, design, size and, of course, material. Most often you can find three furniture options:

1. wooden - most of the floating beds are made of solid wood (cherry, walnut, oak, pine, etc.). Accordingly, the cost of such models is high. A more accessible alternative to them is a sleeping bed with a frame made of chipboard and MDF. The main advantage of wooden products is their high strength. The maximum load they can withstand is 100 kilograms or more. Also, such beds have an aesthetically attractive appearance and are environmentally friendly and safe.
2. metal - floating beds, which basically have a metal frame that is attached to the wall, reliably fixing the sleeping place in the desired position. The main thing in this design is the reliability of the fastenings, which is ensured using special fasteners or welding. The metal frame is powder coated to protect against corrosion;
3. combined - beds in the design of which there is also wood and metal. Usually the metal frame is covered with MDF panels.

Headboard and bedside tables

The headboard for a floating bed is made as a separate block, rigidly attached to the wall. A frame frame is attached to it, which ensures the stability and immobility of the structure. The usual appearance of this unit is a headboard the width of a bed and two shelves on the sides that act as bedside tables. As an option, you can make two hanging bedside tables that do not have supports, which will create the effect of matching the flying bed. The cabinets can be made and installed separately or combined with the headboard into a single unit; this is decided by the owner himself based on his own preferences.

Making a headboard is not very difficult. The main task is the decorative design of the front panel, which can be made in various stylistic options. A variety of materials and colors are used. The selection criterion is usually the resistance of the material to abrasion and contamination, since cleaning the headboard is not always possible. If you use fabric with a soft layer of polyurethane foam installed underneath, cleaning it will become problematic, so you will have to constantly monitor the cleanliness of the front panel. Recently, panels made from wooden planks or artificial imitation wood, without upholstery fabric, have become widespread. This option will allow for periodic cleaning of the headboard, but the surface itself is hard, which is not the best solution for a bed.

Important! When designing the headboard of the bed, you should take into account the color and material of the rest of the furniture in the bedroom. This way you can create the most harmonious atmosphere in the room.

The headboard is mounted to the wall using anchor bolts. Their number is determined by the type of bed support, but should not be less than 2. It is advisable that the headboard has additional support on the floor, this will help reduce the load on the wall and distribute it more evenly.

Making a floating bed: main stages of work

It's not often that you come across a floating bed on sale, and those that do come across are not cheap. Therefore, most often they are made to order, trusted to experienced specialists, or made by hand.

Expert opinion

Smirnova Ekaterina Anatolevna

7 years of experience in interior design, professional architect

This will not only save on purchases, but also create a unique sleeping bed. The main requirement is the availability of the necessary materials and tools, as well as design skills.

The process of making a floating bed involves the following stages of work:

• Drawing up a drawing of the future product with the placement of each part, determining the dimensions and method of fastening.

Advice. On the Internet it is easy to find photos of drawings of such beds, which can be taken as a basis;

• Preparation of the necessary materials (wooden blocks, boards, plywood, metal corners, screws, LED strip, paint, stain, varnish, mattress and much more) and tools (screwdriver, hammer, screwdriver, drill, electric jigsaw, paint brushes, etc.). At this stage, you can calculate the cost of the bed;
• Manufacturing of the frame and base - their dimensions and configuration depend on the design of the bed itself and how many people it will be designed for;
• Installation of LED lighting around the perimeter of the base;

• Laying sheets of plywood on the base, securing them securely with self-tapping screws and PVA glue if necessary. A mattress will be installed on top;
• Making a wooden frame from boards, which is mounted on the sides of the base, as well as the headboard;
• Sanding a wooden surface with sandpaper, coating it with paint and varnish.

After the paint coating has dried, the bed can be used for its intended purpose: lay a mattress on top, lay down beautiful bed linen, etc.

Thus, making a flying bed with your own hands is not as difficult as it might seem. It will delight you with practicality and convenience, giving the bedroom an original look.

Backlight installation

LED strips are used for illumination. They are safe, have a lot of options for choosing colors or brightness levels. They are installed from below on the back wall of the decorative trim of the frame. The main condition for the effectiveness of the lighting is the complete invisibility of the tape from the outside, so that only the illuminated space under the bed can be seen. Installation is carried out on the sides and under the footboard; installing the tape under the headboard does not make sense - this space is not visible, and the side areas sufficiently illuminate the space visible from the outside. To attach the tape, the manufacturers provide an adhesive layer on the back side, so installation will not create any problems. You will need to remove the protective film and simply stick the tape around the perimeter of the inside of the decorative frame. If the condition of the surface does not allow the tape to be firmly attached (the surface is rough or has a noticeable relief), then the connection should be strengthened with glue. You can use “Moment” glue, gel second glue, transparent thick “Titan”. These materials are suitable for attaching the tape to almost any surface and will ensure reliable fixation.

More detailed or visual information can be obtained in various videos, of which there are many on the Internet, for example:

A flying or hovering bed, created with your own hands, will save a significant amount of money and create a unique, magical interior in the bedroom. To make it, you will not need any specific tools or materials, but you must have skills and experience working with wood or metal, otherwise the quality of the product will be low. Design skills also don’t hurt, although there are many design options for such beds online, you can choose any one you like. All materials needed for the work are commercially available and quite affordable. Prices for materials are relatively low, in addition, there is always the possibility of choosing materials of one or another price category. All that is required from the master is his experience, diligence and patience, which will certainly be rewarded and will be able to create a cozy and comfortable environment in the bedroom.

How to make a floating bed with your own hands step by step

Remember the fairy tale about the flying carpet? Probably everyone, reading or listening to this story, dreamed of finding themselves on it. Now, it turns out, you can create such a miracle with your own hands.

This is the so-called floating bed. The peculiarity of this sleeping place is that it is made in such a way that the legs are not visible, and is decorated with lighting from below.

This creates a feeling of miracle: your bed floats above the floor. Visually, this model greatly decorates the interior of your bedroom.

Of course, it’s easier to purchase a ready-made one, but this is not always possible. Sometimes it is difficult to choose the size or you are not satisfied with the material.

It should be noted that the cost of such furniture is much higher than a regular bed. If you want to perfectly fit the bed into your bedroom, then it is better to take the time and make it yourself.

Models

Furniture with a flying effect varies in shape:

• The most popular are traditional rectangular options. Also, a fashionable round bed will look impressive in the bedroom interior.
• Rectangular bedroom furniture is most often attached to the wall with its backs or both sides at once (if it has a corner design). Behind the headboard in such specimens there is a corner that ideally attaches to the wall.
• The legs in floating beds are securely hidden. Today, such furniture is represented by options with one support in the center. Rays extend from it in different directions. Thanks to the right design, the load is optimally distributed across the beams, which makes the bed reliable and designed to withstand heavy loads.

• The supports are sliding. Their height can be adjusted at your discretion.
• There are beds in which several legs (3-4) are installed at once . As a rule, they are located closer to the central part and are not visible at all. Particularly popular today are bed models in which such hidden parts are made of tempered glass.

• The options in which the side skylight is semicircular look interesting in the bedroom interior. The bases of such models seem to be raised, but the sleeping area itself remains level.

Nuances of a floating bed

We recommend installing such a bed in your home. This wonderful piece of furniture has the following advantages:

• As a rule, it is double. You will get a very decent place to sleep. And in what composition you will use it, this is no longer so important.
• The base of the product is made of wood or metal. It is mounted to the wall, and the legs are installed in such a way that they are not visible at eye level.
• Bottom lighting, in addition to emphasizing the effect of flight, makes it possible to create a romantic mood and save on overhead light or a night light.
• Such a bed can completely transform a room. Whether you have high-tech, loft or classic – the product will fit perfectly into everything and will decorate your bedroom favorably.
• There is a wide range of options. This allows you to take into account any taste and any requests of the owners.

It is important to note that the design is difficult to install, and you will most likely need the help of a relative, neighbor or a furniture assembly specialist.

Expert opinion

Smirnova Ekaterina Anatolevna

7 years of experience in interior design, professional architect

You also need to think about the fact that the drawer under the bed will make the structure heavier. Therefore, take care of a furniture pencil case, chest of drawers or wardrobe for bedding.

How to make a working drawing

If all the work is planned to be carried out independently, then it is not decisive in what form the drawing will be drawn up. The main goal that is pursued when creating it is to carefully think through all stages of the work, clarify the dimensions, methods of connecting elements and parts, clarify some points and detect possible errors and miscalculations. It is imperative to draw up the most complete list of necessary materials (indicating their quantities) and tools that will be needed when performing the work. It is necessary to draw the design to scale in order to be able to evaluate your plan from an aesthetic point of view and, before it is too late, make some changes if they are needed.

Attention! Drawing up drawings of parts, the production of which will have to be ordered from specialized organizations, must be carried out in accordance with current technical standards and rules. Otherwise, discrepancies will arise that can lead to the production of inappropriate components and parts.

Tools for work

To make a bed relatively quick and of high quality, make sure you have the following tools, especially since they are not in short supply:

• screwdriver, screwdrivers, hammer;
• electric drill;
• saw or jigsaw;
• building level;
• tape measure, pencil.

Required materials for a floating bed

To make a bed, you need to purchase:

• orthopedic mattress;
• a sheet of plywood for the bottom;
• wooden beams, boards for sidewalls and headboards;
• fasteners (screws, corners). PVA glue;
• materials for wood finishing (varnish, stain);
• LED lighting.

The nuances of working with duralight

In view of the technical features of such a lighting device, several points should be noted that should be taken into account when making lighting from a light cord:

1. if you are joining several pieces for a bed, make sure they have the same characteristics;
2. connectors are selected according to the shape and number of contacts of the connected cords;
3. The connection points must be dry without visible damage to the insulation;
4. before turning it on, unwind it and check its functionality, but you can assemble and mount the backlight from duralight only in the switched off state;
5. the cord has a special hermetic sheath, which you must keep intact, but if you damage the silicone during the installation process, this place is sealed with insulation;
6. If you want the cord to not only light up, but also enter the blinking mode, install the controller along with the adapter.

Step-by-step instruction

Let's look at the main stages of making a floating bed:

• Make the frame according to your measurements. To do this, use screwdrivers or a screwdriver, nails, and a hammer. If necessary, trim excess wood with a hacksaw or jigsaw.
• Board base. It is made, as a rule, 2 times smaller relative to the area of ​​the frame.
• Fixing lighting. LED lamps are most often used; they are mounted on all sides of the bottom of the bed.
• Installation of plywood on the frame and its installation. For better fixation, use adhesive (PVA) and self-tapping screws. Buy a sheet of plywood thick enough to support the weight of the mattress and you.
• Making a frame. Boards are attached along the perimeter of the frame, thus forming the side walls of your bed.
• You can really make a headboard yourself or buy a ready-made one. It can be made in various shapes: rectangular, oval, square, rectangular.
• Sanding the boards of the entire product. Final coating with varnish and stain.

If you carefully calculate everything and make every effort, then a miracle bed will appear in your home. It’s especially nice that you made it yourself.

UNUSUAL HOMEMADE BED WITH YOUR OWN HANDS - HOW TO MAKE IT?

You can give your bedroom an unusual look with a floating bed. And you can do it yourself.

The floating, or “levitating” bed gets its name because its support points are not visible. It seems as if the furniture is literally hovering above the floor.

However, the feeling of fragility is deceptive - the bed is very stable and reliable. The support is right here.

It’s just that it’s small in size (relative to the bed itself) and is located so that you can notice it either from a great distance or by looking under the bed.

I’m not a professional carpenter, but I decided to try my hand at making a floating bed measuring 200x180 cm. I looked at all the available materials on the Internet, took a screwdriver, a drill and a jigsaw, the boards were already in stock, I bought only the missing parts, and the work began!

EVERYTHING YOU NEED FOR THIS ARTICLE IS HERE >>>

Under bed storage drawers

If you can't make a bed with storage or you already have a regular bed, you can always make storage boxes separately. It is very convenient and functional, and if you decorate it beautifully, it is also stylish. Check out eight examples of DIY under-bed storage boxes below.

Box under the bed for storing things

The space under the bed is one of those places that is often underused or cluttered with toys or dirty clothes. There are many ideas on how to solve this problem. For example, you can make boxes like this. Not only will these boxes give you tons of storage space, but they look amazing at the same time. The boxes are inexpensive to make and easy to assemble. This project is a great project for beginners, you only need a few supplies and can complete the project in one day.

Now your little ones will have plenty of space to store their clothes, toys, books and much more!

Photo source: www.lifestorage.com/blog/diy/under-bed-storage-diy/

DIY under-bed storage boxes

These foldable under-bed storage bins are the perfect space-saving solution for storing shoes, bags, and other items that are awkward to store in a closet! Measure the width and height of the space under the bed frame. Then cut the wood into four pieces. The goal is to make the box rectangular in shape, with the longer parts being the sides and the short parts being the front and back. Pre-drill two holes at each end. Stack two sets on top of each other to save some time! Gather the corners of the box and glue them together with wood glue. Attach the two ends to each other at a 90 degree angle. TIP: Use a corner bracket clamp. Do this on all four corners until you have a rectangular box! Cut the plywood with a jigsaw or circular saw to make the base. Screw the base into the box frame. Then screw wheels to all four corners and voila, you have a box that rolls. By the way, when measuring the size of the boxes, do not forget to take into account the size of the wheels! Now for the decor. You can simply stick wallpaper on the inside of the drawers. And then the pens! Screw them to the front of the box, pre-drilling holes towards the center. Don't forget to measure the width and height.

How to Make Under Bed Storage Boxes

For extra under-bed storage, check out how to make simple plywood drawers on wheels.

The boxes are very easy to make with your own hands; you can even enlist your children to help you and paint them together to your liking. A short instruction with lists of materials and cutting instructions can be found on the website. See step-by-step photos of the master class below in the gallery of step-by-step photos.

DIY storage drawer

These cool drawer drawers with platinum baskets are perfect for organizing your kids' room! Read on to learn how to make DIY under-bed storage boxes and add more space to your kids' bedroom (though they'll fit in an adult's space too)! Start with the wood you will use and the size. You will need to calculate everything for your bed yourself, because each bed is at a different height from the floor. Here are some tips for measuring. Measure the distance from the floor to the very bottom of the bed. Next, determine the width of wood you can use by adding the dimensions of the wheels and the thickness of the plywood on the bottom of the bed. Here the rollers are 4 cm high, and the side boards are 15 cm. Thus, the height of the drawers is 19 cm. The final dimensions of the drawers are as follows. The front of the drawer is 94 cm. The sides are 61 cm. This is the size the plywood was cut to because it is screwed to the bottom of the drawer frame. Detailed instructions, as well as a list of necessary materials, can be read on the website, link under the gallery. Oh, and add bumpers for the drawers so that when the kids close the drawers they don't hit the bed.

Photo source: www.tipsfromatypicalmomblog.com/2015/11/diy-under-bed-rolling-storage-drawers-tutorial.html

The first element - the base of the bed - is assembled

To make the lower part (support of the floating bed), I needed 2 boards measuring 1920x200x25 mm, 3 boards measuring 960x200x25 mm and 2 boards 1010x200x25 mm. There was no 200 m wide board available, so we had to make it composite, from two 100 mm boards.

On a flat surface, I began assembling according to the drawing made in advance. In the right places in the boards I drilled holes for self-tapping screws. To prevent the stock from creaking in the future, I coated all joints with silicone glue.

IMPORTANT. Unfortunately, such glue was not enough, so I laid thick polyethylene on the horizontal joints. During operation, it became clear that modifications with glue and polyethylene turned out to be very effective. For two years - not a single squeak!

Then I checked the diagonal with a tape measure. Everything turned out to be accurate. For additional strength, the corners of the base were reinforced with additional posts.

For the top of the bed I needed 5 bars measuring 1710x100x50 mm, 2 bars each 2010x100x50 mm and 350x 100x50 mm, 5 bars 560x 100x50 mm and 3 boards 560x100x25 mm. I used 400x100x25 boards to secure the stock to the base.

I pre-connected blanks 560x100x50 mm with 350x100x50 mm in the shape of the letter “T”. Next, from bars 2010 mm and 1710 mm long, I assembled a rectangle measuring 2010 × 1810 mm.

To hold the diagonal, I attached tie boards to the corners of the rectangle. I drilled holes in the boards ahead of time, but did not connect the parts yet.

And finally, I connected the parts according to the drawing, starting with 560 mm long bars and “T” blanks. Let me mention again: I coated all joints with silicone! It ended up taking several hours to assemble the bed frame.

It's time to make the headboard. I decided to decorate it with a carriage tie. This is a popular technique for decorating upholstered furniture; it got its name due to the fact that it was originally used for the interior decoration of carriages.

On an OSB board measuring 1810x1000 mm, I marked a grid with a side length of 200x215 mm. This made it possible to identify and drill the places where the buttons were attached. Then I transferred the drawing onto a sheet of special furniture foam rubber (density 25) and glued it to the OSB using PVA-M Extra glue. From below I left 300 mm of the slab, not sealed with foam rubber.

Then I covered the headboard with fabric. I started laying it from the top corner.

I’ll warn you right away: when determining the size of the canvas, you need to make a reserve - about 40 cm on each side. Then I installed buttons in the right places using a thick furniture needle.

I secured the threads on the wrong side with a furniture stapler. And later I used it to secure the edges of the fabric.

The lower indentation of 30 mm, which was left without foam rubber, was also covered with fabric. It took about a day to complete the headboard, taking into account the glue drying.

Expert opinion

Smirnova Ekaterina Anatolevna

7 years of experience in interior design, professional architect

The final stage is assembling the bed. I installed the base and upper part of the bed in a permanent place and connected them using small boards.

IMPORTANT. If you have animals (cats), you need to close all the holes inside the base of the bed.

I screwed an OSB sheet on top, but I recommend using natural wood (without glue) or an orthopedic base. The base was leveled relative to the headboard so that the foam was raised above the base by 200 mm, that is, to the height of the mattress.

The sides of the bed were decorated with panels (shelves) made of chipboard. For this purpose, in a large furniture store I bought furniture shelves measuring 2700 x 300 x 16 mm (4 pcs.) and 1200 x 300 x 16 mm (6 pcs.), as well as a 19 mm wide melamine edge strip with an adhesive layer.

IMPORTANT. It was not possible even to very carefully cut through the laminated chipboard panels with a jigsaw without “casualties”: there were still several chips in the coating. To minimize this effect, you need to take special files for laminated chipboard (with small, non-directional teeth). So if you do something similar, it is better to cut the slab on a machine or in a specialized store.

I glued the edge strip onto the laminated chipboard cuts with an iron, through cotton fabric, cut off the excess and sanded it.

I fixed the panels with a clamp (there was no assistant) and drilled holes with a 5 mm confirmat drill (Euroscrew), made a 6.3x50 mm HEX screw tie (100 screws were needed). These screws have a special pitch and cutting angle, which increases the reliability of the connection.

From the remnants of chipboard I assembled shelves behind the head of the bed. They provide additional counterweight for better stability of the bed, as well as a large top shelf and 3 small side shelves for placing interior items and storing things and bed linen.

Types of bed designs with a floating effect

Floating furniture hangs in the air thanks to specific mounting methods.

• On one leg. A floating bed can only have one support in the center of the base. Decorative lighting distracts attention from the leg, which is already almost invisible due to its location. Sometimes rays radiate from the central support, which allow the weight to be evenly distributed. With this fastening, the product will withstand a load of up to 300 kilograms.
• On magnets. The author of floating magnetic furniture is the Dutch architect Janjaap Ruijssenaars. The designer's idea is based on the principle of magnetic levitation. Magnets are built into the frame of the product and into the floor, which keep it in the air. The floating sleeping bed stays in place thanks to four cables. The magnetic bed can support a weight of up to 600 kilograms. It is not suitable for people with pacemakers due to the magnetic field.
• On a metal frame. The main advantage of a metal frame is the reliability of the fastenings. The metal frame must be powder coated to prevent corrosion. Usually the metal frame is covered with a body made of MDF or solid wood.
• Suspended from the ceiling. The bed can be attached to the ceiling with strong ropes. This design has increased safety requirements. For a child's room, it is recommended to use steel cables instead of rope ropes.
• Attached to the wall. A headboard attached to the wall will give the structure additional stability.

“Flying” furniture looks weightless, as if challenging gravity.

The photo shows a hanging bed in an oriental style. Strong ropes hold the bed made of solid wood with layers of polymer resin.

With invisible legs

These models are the most popular and affordable. The peculiarity of a bed with invisible legs is that there is only one support located in the center of the base. In addition, such beds are distinguished by the presence of decorative lighting, which is designed to divert attention from the legs and thus provide a floating effect. Some beds have rays radiating from the central support, which help distribute the mass evenly. It is thanks to this that the bed is able to cope with enormous loads.

Dimensions

Today in the store you can find a bed with a floating effect of any size. The most common are the standard options with a length and width of 160x200 cm, 180x200 cm and 200x200 cm. The “royal” models are more spacious, their dimensions are 200x220 cm.

Such beds should be purchased only from trusted and high-quality manufacturers, so as not to run into a weak and unreliable design.

Many furniture stores make “floating” beds to individual measurements. Such a bed will be expensive, but it will be ideal for your bedroom.

Wall mount

The wall mount gives the hanging bed a mysterious look. If you look at it from a certain angle, the attachment point is not visible, and the stock appears to be floating in the air. Wall fixation provides the same stability as the ceiling option, but is less common.

The low popularity is explained by the more complex design of the supporting structure; you can’t do without supporting beams and massive corners. The following life hacks allow you to add stability to a wall mount:

• The design is equipped with a central leg against the wall. Sometimes it is made of transparent plastic, and then the detail does not catch the eye.

• The product is fixed according to the principle of a berth on a train: with the help of side supports that create the effect of a folding bed, and metal cables. In this way, you can place two beds one above the other and save space, which is important if you need to arrange a hanging children's bed.
• The bed is mounted in the corner of the room. The load is distributed over two walls, which increases reliability.
• The main feature of the structure attached to the wall is that it does not swing.

With frame

The main advantage of a floating bed on a metal frame is the reliability of its fastening. Such models are able to cope with any load, which has a positive effect on their durability. When choosing such beds, you need to make sure that the metal frame is additionally treated with powder paint, which is designed to provide reliable protection against corrosion. In most cases, the metal frame is covered with a wooden body, which gives the product a more elegant appearance.

Creating a metal frame

Making a base for a mattress using a metal profile or rectangular pipes is similar to working with wood, but for joining you will need a welding machine and the ability to handle it. Bolted fastening of components has the right to exist, but it will require a lot of labor and time. This type of installation is more difficult to implement.

The process of securing the slats under the mattress will also differ. First, a metal corner with drilled holes in 15 cm increments is welded inside the finished frame. Then slats or lamellas are screwed to this corner. In another way, the support frame is assembled, which most often has one connection in the center and branches back and forth in the form of a trapezoid. It is better to fasten the frame (leg) to the base using a bolted connection so that it can be removed during transportation.

It is important to know: at each stage it is necessary to clean the cuts and welds with an angle grinder.

How to make a wood frame

Let's look at the process of how to make a floating bed with your own hands. First, you need to purchase solid wood, carefully inspecting each board for chips, cracks, and the presence of knots. It is advisable to purchase sanded and dried boards. You need to let them lie in the bedroom for several days so that they absorb moisture from the environment and do not become deformed after cutting and fastening.

For the base of the frame, wooden blocks 50 mm thick are suitable, from which 2 blanks are cut out, equal to the length of the mattress and its width minus double the thickness of the block. It is necessary to additionally cut 3 more short boards, from which the supporting transverse mesh will be twisted.

The 4 main blanks are connected using metal corners and self-tapping screws. The cross beams are secured with long bolts into ready-made drilled holes through the side board. Additionally, all connections are treated with glue.

To control the correct assembly of the frame, I advise the master to use a long stick placed diagonally. A slight shift will immediately disrupt the length of the two lines relative to each other. Then it is necessary to add reinforcement in the form of thinner planks in a checkerboard pattern between the transverse beams.

After the base for the mattress is ready, you need to make a support frame. Its dimensions should be one third smaller than the frame and allow placement under its central part. The process consists of the steps of creating a square or rectangular wooden box with one cross reinforcing board.

The final stage of manufacturing is fixing a solid sheet of plywood or chipboard on which the mattress will directly lie. You can create a slatted or slatted base.

Ceiling mount

This is the traditional and most common method of fixing an air bed. The ceiling mount has the following features:

• The bed is secured at one or several (usually 4) points. Fasteners are mounted in the ceiling or open ceiling beams if they are provided for in the style and are part of the structure and not decor.
• The most important task is to calculate the load and select reinforcement based on it. The height above the floor is chosen according to your taste; The optimal height is 30 cm.

• Typically, durable metal anchors are chosen for ceiling mounting. Four attachment points are needed for a classic rectangular bed. Round hanging beds from the ceiling are usually fixed at one point.
• The bed is suspended using nylon ropes, metal chains or cables fixed in the corners of the furniture.

• You should not choose a place for furniture close to a window or wall. After installation, the structure will remain mobile and will swing. To reduce the range of movement, the place is chosen so that the bed is leaning against the wall on one side; then one of the surfaces is protected with soft material (for example, felt).
• If you want to get rid of swinging, cables and chains can be replaced with crossbars or metal poles. To fix a static structure, do not choose anchors, but round or corner elements made of metal.

With drawers or cabinet

Bedside tables and bedside tables have become an invariable attribute of a comfortable bedroom. Bedside furniture hung on the wall will look organic next to the floating bed to enhance the illusion of levitation in the interior.

With ropes

Such models are attached to the ceiling using strong and reliable ropes. It should be noted that the installation of this bed requires strict safety measures. If we are talking about a children's room, then it is best to use steel cables, which can guarantee the safety and immobility of the bed even in the case of increased load. The fact is that children often jump on the bed, which can cause rope ropes to break, so it is best to use steel analogues.

Double

The levitating bed, thanks to the reliable design of the fastenings, can easily support the weight of two adults. The length of the sleeping place is calculated based on the height of the one who is taller in the pair plus 10 centimeters.

On magnets

Such beds first appeared in the Netherlands and immediately became popular throughout the world. This idea is based on the principle of magnetic levitation, which allows you to create the effect of a bed floating in the air. The bottom line is that powerful magnets are installed in the bed frame and floor, which ensure floating in the air. In addition, additional pipes are used here to ensure the bed is still and secure. This combination allows the product to cope with a weight of up to 600 kg. The only limitation applies to people with pacemakers, since the magnetic field can create some interference.

You can also find other models on the market that differ in their lifting mechanism, carriage tie or upholstered headboard. The choice of a specific model depends on the personal preferences of the owners and the layout of the room itself.

With soft headboard

The floating bed itself is laconic, so designers actively use the headboard to realize their original ideas. The most popular decor option remains soft upholstery made of tapestry, leather or textiles. The upholstery is made in the form of a carriage tie, decorated with rhinestones and photo printing. The role of the headboard can be performed by a wall with soft volumetric panels.

Combined method

The combined fastening is considered the most reliable and safe, and therefore is often used in children's rooms. It is also chosen if there are doubts about the strength of the ceiling. The method combines fastening the product to the ceiling with simultaneous fixation to the wall or floor, which eliminates swaying. For installation, the following scheme is usually used:

• Fastenings are attached in the corners of the headboard for fixing it near the wall.
• Cables or chains are attached to the legs, which are suspended from the ceiling with hooks.
• Sometimes a window sill or podium serves as additional support for the bed.

With lifting mechanism

Thanks to the lifting mechanism, storage space appears at the base of the sleeping bed. Unfortunately, this design makes the product heavier and requires additional strengthening of the supports.

The photo shows a floating bed in a modern style with additional storage space.

WHAT DOES IT COST ME TO MAKE A HOMEMADE BED?

I had the wood for the frame and screws in stock.

Furniture shelf laminated chipboard size 1200x300x16 mm, wenge - 6 pcs. 166 rub. = 996 rub. Furniture shelf laminated chipboard, 2700x300x16 mm, wenge – 4 pcs. for 419 rub. = 1676 rub.

OSB-3 (OSB-3) 9x1250x2500 mm (Europe) – 2 pcs. for 467 rub. = 934 rub.

Drill for confirmation 5 mm high-pressure – 50 rub.

Galvanized screw tie 6.3×50 HEX (100 pcs.) – 142 rub. Plug for tie screw HEX D5mm, black, 100 pcs. – 50 rub. Melamine edge tape with glue, 19 mm, wenge, 5m-62 rub.

Sintepon 2×2 m – approximately 200 rubles.

Buttons and rope - approximately 400 rubles.

From the editor. Often, from below, along the perimeter of the frame of a floating bed, LED lighting is attached - a strip with a power supply, so that the LEDs are not visible from the outside. When it is turned on, the bed, the base of which is not visible from a height of human height, literally floats in the air.

Bed lighting with LED strip

An LED strip is a board with LEDs placed on it. It also has its pros and cons. The advantages include the following:

• easy installation due to the adhesive layer;
• ease of use, compactness;
• the price is lower than for duralight.

Flaws:

• low moisture resistance;
• lack of protection from mechanical damage.

Most often, LED strip is used to illuminate the bed. Now let's look at the installation methods step by step.

Nuances and important design points

One of the most important nuances is the choice of material for the structure. We have 4 choices:

1. Wood. If we decide to create a house structure with our own hands, we should focus on this material. Wood is easy to cut and process. But it is recommended to choose hard wood, and take care of protection from moisture in advance. Screws and bolts are suitable as fastening parts. The strength of a wooden bed will depend on the quality of the chosen material, fastenings, and correct assembly.
2. Metal. Processing is several times more difficult, since it requires the use of a welding machine. You can use only bolts as fastenings, but this is only suitable if welding is not possible. You need to pay special attention to the fastening parts, since they break most often. The material itself is very durable. A combination of bolting and welding can also be used to allow the structure to be disassembled if it needs to be moved.
3. Combination of materials. We can use both wood and metal. This will make assembly work easier, and the weight of some structural parts will be lower. You can use strong metal to create fastenings and places that need to be made strong. And wood is suitable for parts that are difficult to process. This will solve all the problems that arise during assembly.
4. Sheet materials (MDF, plywood and fiberboard). With their help, the place to lie can be made as flat as possible. In addition, they are suitable for creating additional devices (bedside tables and shelves next to the bed). We need polyurethane foam or foam rubber to create soft areas of the bed.

Yard and garden

When decorating your home, you shouldn’t forget about what’s outside. Let's start with the entrance area. From concrete blocks and a couple of wooden slats you can make a cute and comfortable table where flowers, a watering can, a lantern or anything else will live.

By the way, you can make various benches from concrete blocks, decorate flower beds, build a barbecue, and even make flower pots. It all depends on your imagination.

You can also make stylish ottomans and armchairs with your own hands. You need old tires, liquid nails and thick rope. The finished structure can be painted in any color. These ottomans are suitable for both indoors and outdoors, because they don’t mind rain.

Boxes or pallets made of wood can serve as the basis for a garden cabinet. Here you can store various flower accessories, pots, watering cans and other tools. And if you leave a flat work surface on top, you can make something or replant flowers.

What could be unusual in a flower pot? It would seem - nothing. However, here you can surprise everyone. Plant succulents in a birdcage. When they grow, it will be very beautiful. And instead of a regular hanging pot, you can use an old chandelier.

An ordinary children's inflatable pool can be used as a sofa. Just put a blanket or blanket inside and cover the sides with pillows.

It’s so beautiful to use candles in the garden, but they are constantly blown out by the wind. To prevent this from happening, you can make candlesticks from empty tin cans or ordinary glass ones. You can decorate everything with stones or ribbons if desired.

These, of course, are not all ideas for home and garden, only a small part of what you can do with your own hands. You just need to not be afraid to experiment and fill your home with cute and beautiful things.

Inspiration:

Drawings and diagrams

The main goals of creating a drawing are to think through all the work, clarify the details that will secure the design and detect potential errors.

The average thickness of the board that will be used for the frame is 5 cm. Construction stores most often sell pine boards. You need to calculate the amount of material (depending on the size of the person).

Where to begin

The beginning of all work on creating a flying bed is careful preparation. It includes:

• Choosing a certain type, design solution, option for the appearance of the bed.
• Creating a project, working drawing or product plan.
• Purchase of all necessary materials.
• Purchasing the necessary tools.

At each stage of preparatory work, the final development of the project is carried out, various minor issues arise and are promptly resolved.

Note! The first point that you must begin the preparation process with is the purchase of a mattress. Its dimensions are very important; all working drawings, dimensions of support platforms, and the amount of materials are tied to the parameters of the mattress. Not everyone can make it themselves; most often a finished product is used, and it must be at the user’s disposal by the time work begins.

Advantages and disadvantages

In addition to the unusual design, the flying bed has a number of other advantages:

• The risk of loosening or falling due to broken legs is completely eliminated. The frame is firmly attached to the wall.
• Along with other standard models, flying stocks look unusual and original.
• A wide selection of different designs will allow you to purchase a product to suit any style.

Expert opinion

Smirnova Ekaterina Anatolevna

7 years of experience in interior design, professional architect

The disadvantages include the complexity of installation. You need to have some knowledge of carpentry and construction. A negative characteristic is the inability to equip drawers and storage shelves under the bed.

The use of a floating model obliges the housewife to carefully monitor the order in the house, otherwise even a two-day layer of dust will be visible to the naked eye.

Functional Features

Flying beds have taken their rightful place among both professional designers and people, due to their originality and unusual appearance. We can’t help but mention its functionality:

• Even the most classic look of a bedroom, thanks to such a bed, will acquire originality;
• the sleeping place is quite spacious, cozy, designed for two;
• LED lighting serves as additional lighting at night and creates a romantic mood;
• due to the strong fastening of the bed to the wall, a floating effect is created;
• The flying bed can be used by both adults and children.

Choosing a bed design

A double bed, which seems to hover above the surface, can itself decorate the bedroom and create a full-fledged interior without additional pieces of furniture and decorative ornaments. Therefore, it is difficult to choose the design that will fit well into the existing environment.

Illumination of the under-bed space creates a special feeling of floating and highlights the area that always remains hidden. For this reason, designers advise purchasing a bed immediately after renovation and before the bedroom is furnished, so that it is possible to organize the space around it.

If you plan to make it yourself, you need to be especially careful when choosing a design so as not to encounter insurmountable difficulties during the creation process.

Drawing up a design project

Before work, you need to prepare a drawing of a floating bed to make yourself.
First, you need to decide on the dimensions of the furniture being created, select the necessary material, decide which parts will be included in the design, and clearly imagine the appearance of the future product. The first stage is to view photos of finished models and select the appropriate option

Attention should be paid to the materials from which the furniture is made, dimensions, and additional elements used for decoration. To determine the dimensions of an unusual design, you need to make accurate measurements of the room in which the bed will be installed

Then you need to choose a mattress, the dimensions of which will also determine the design of furniture with the levitation effect.

After determining the width and length, the issue of the dimensions of the support is resolved. It is better to look at the furniture from the greatest distance and make a sketch. Only then can you finally choose the size of the support and decide how much smaller it should be relative to the main part of the structure. Please note that the support should not be narrow, otherwise the bed will sway.

There are model options that do not require support. In this case, the flying structure has a thick headboard and an L-shaped steel pipe, a short section of which is firmly fixed to the wall. The frame is made strong enough not to wobble or break even when sitting on the edge of the bed. It is possible to manufacture an intermediate version with a smaller support made of high-strength transparent, almost invisible material.

Then the configuration and size of the headboard is selected, which is one of the main parts of the structure and determines the design of the bed. The color of the product and decorative elements are considered. Next, a diagram of the floating bed is drawn up, structural elements, connections, and parts used for reinforcement are worked out. During the work process, you need to check the results more often, measure parts several times in order to eliminate possible errors at the initial stage, and not at the end of manufacturing the product.

The drawing is drawn up both for the entire structure and for the parts. For precise manufacturing, not one, but several projections are performed. Once you have completed drawing the plan, you can begin purchasing materials and tools.

What to look for when buying a floating bed

A floating bed with lighting is quite expensive, so you need to approach the purchase responsibly, choosing trusted manufacturers.

If we are talking about a wooden product, you need to make sure that oak, cherry or pine is used in the creation. They are durable and can withstand up to 100 kg per bed.

Before use, metal frames must be carefully inspected and the joints checked.

All fasteners must be included with the product, including dowels for wall screwing.

Types of Home LED Lighting

For home interiors, LED strip (LED strip) or duralight are usually used. They are energy saving and durable. But there are some differences between them. To make choosing easier, I suggest you understand their advantages and disadvantages.

Illuminating the bed using duralight

Duralight is a flexible cord with LEDs inside. Its main advantages include:

• protection from any damage;
• resistance to temperature changes;
• waterproofness and strength of the material.

Flaws:

• the price is higher than for LED strip;
• the glow is not very bright.